Leviton 41OUM Series Скачать руководство пользователя страница 33

Страница: 33 / 33

Installation Guide
Power Monitoring
Series 4100 Modbus

Problem

Cause

Solution

The maintenance wrench

icon appears in the power
meter display.

There is a problem

with the inputs to the

power meter.

See the Alert sub-menu or the Diagnostic Alert Modbus Register 146

The display is blank after

applying control power
to the meter.

The meter is not

receiving adequate
power.

Verify that the meter control power are receiving the required voltage.
Verify that the heart icon is blinking.

Check the fuse.

The data displayed is

inaccurate.

Incorrect setup values

Verify the values entered for power meter setup parameters (CT and PT ratings,

system type, etc.). See the Setup section.

Incorrect voltage inputs

Check power meter voltage input terminals to verify adequate voltage.

Power meter is wired

improperly.

Check all CTs and PTs to verify correct connection to the same service, CT and PT

polarity, and adequate powering. See the Wiring Diagrams section for more
information.

Cannot communicate

with power meter from
a remote personal
computer.

Power meter address is

incorrect.

Verify that the meter is correctly addressed (see Setup section).

Power meter baud rate

is incorrect.

Verify that the baud rate of the meter matches that of all other devices on its

communications link (see Setup section).

Communications

lines are improperly

connected.

Verify the power meter communications connections (see the Communications

section).

Verify the terminating resistors are properly installed on both ends of a chain of units.

Units in the middle of a chain should not have a terminator.

Verify the shield ground is connected between all units.

Sign of one phase (real

power) is incorrect

CT orientation reversed

Remove CT, reverse orientation, reconnect (qualified personnel only)

Troubleshooting

China RoHS Compliance Information

(EFUP Table)

部件名称

产品中有毒有害物质或元素的名称及含量

Substances

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr(VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

电子线路板

O =

表示该有毒有害物质在该部件所有均质材料中的含量均在

SJ/T11363-2006

标准规定的限量要求以下

X =

表示该有毒有害物质至少在该部件的某一均质材料中的含量超出

SJ/T11363-2006

标准规定的限量要求

Z000057-0A

Содержание 41OUM Series


































Результаты поиска

Содержание 41OUM Series

Отзывы:

Похожие инструкции для 41OUM Series

Бренды по названию

Популярные бренды

Leviton 41OUM Series, Инструкции по установке

Результаты поиска

Содержание 41OUM Series

Отзывы:

Похожие инструкции для 41OUM Series

Бренды по названию

Популярные бренды