LevelOne ProCon GSW-1291 Скачать руководство пользователя страница 14

Страница: 14 / 234

User Manual

Publication date: May, 2005

Revision A1

2. Installation

2-1. Starting GSW-1291 Up

This section will give users a quick start for:

Hardware and Cable Installation

- Management Station Installation

- Software booting and configuration

2-1-1. Hardware and Cable Installation

At the beginning, please do first:

⇒

Wear a grounding device to avoid the damage from electrostatic discharge

⇒

Be sure that power switch is OFF before you insert the power cord to power

source

•

Installing Optional SFP

Fiber Transceivers to the GSW-1291

Note: If you have no modules, please skip this section.

•

Connecting the SFP Module to the Chassis:

The optional SFP modules are hot swappable, so you can plug or unplug it
before or after powering on.

1. Verify that the SFP module is the right model and conforms to the chassis

2. Slide the module along the slot. Also be sure that the module is properly

seated against the slot socket/connector

3. Install the media cable for network connection

4. Repeat the above steps, as needed, for each module to be installed into

slot(s)

5. Have the power ON after the above procedures are done

Fig. 2-1 Installation of Optional SFP Fiber Transceiver

Содержание ProCon GSW-1291











































































































































































































































Результаты поиска

Содержание ProCon GSW-1291

Отзывы:

Похожие инструкции для ProCon GSW-1291

Бренды по названию

Популярные бренды

LevelOne ProCon GSW-1291, Руководство пользователя

Результаты поиска

Содержание ProCon GSW-1291

Отзывы:

Похожие инструкции для ProCon GSW-1291

Бренды по названию

Популярные бренды