LevelOne GSW-2494 Скачать руководство пользователя страница 13

Страница: 13 / 227

User Manual

Publication date: May, 2005

Revision A1

2. Installation

2-1. Starting GSW-2494 Up

This section will give users a quick start for:

Hardware and Cable Installation

- Management Station Installation

- Software booting and configuration

2-1-1. Hardware and Cable Installation

At the beginning, please do first:

⇒

Wear a grounding device to avoid the damage from electrostatic discharge

⇒

Be sure that power switch is OFF before you insert the power cord to power

source

•

Installing Optional SFP

Fiber Transceivers to GSW-2494

Note: If you have no modules, please skip this section.

•

Connecting the SFP Module to the Chassis:

The optional SFP modules are hot swappable, so you can plug or unplug it
before or after powering on.

1. Verify that the SFP module is the right model and conforms to the chassis

2. Slide the module along the slot. Also be sure that the module is properly

seated against the slot socket/connector

3. Install the media cable for network connection

4. Repeat the above steps, as needed, for each module to be installed into

slot(s)

5. Have the power ON after the above procedures are done

Fig. 2-1 Installation of Optional SFP Fiber Transceiver

Содержание GSW-2494




































































































































































































































Результаты поиска

Содержание GSW-2494

Отзывы:

Похожие инструкции для GSW-2494

Бренды по названию

Популярные бренды

LevelOne GSW-2494, Руководство пользователя

Результаты поиска

Содержание GSW-2494

Отзывы:

Похожие инструкции для GSW-2494

Бренды по названию

Популярные бренды