LevelOne FCS-4201 Скачать руководство пользователя страница 58

Страница: 58 / 66

Network Camera User’s Manual

58/66

backup file. If you have set up a fixed IP or other special settings for your device, it is not
suggested to upload a settings backup file.

“Upgrade firmware”

Select the firmware file and click upgrade button. Please be

aware that you should not turn off the power during updating the firmware and wait for
finish message.

Warning:

The upgrade firmware procedure cannot be interrupted. If the power

and/or network connection are broken during the procedure, it might possibly
cause serious damage to the Network Camera.

Note: When upgrade firmware please wait for 210~360 seconds, and then you
can connect to Network Camera again. The system will restart and require the
installer program to set up the network again.

Содержание FCS-4201



































































Результаты поиска

Содержание FCS-4201

Отзывы:

Похожие инструкции для FCS-4201

Бренды по названию

Популярные бренды

LevelOne FCS-4201, Руководство пользователя

Результаты поиска

Содержание FCS-4201

Отзывы:

Похожие инструкции для FCS-4201

Бренды по названию

Популярные бренды