Leuze electronic 50038948 Скачать руководство пользователя страница 62

Страница: 62 / 74

Online commands

BCL 8

Leuze electronic

autoConfig

Command

’CA’

Description

Activates or deactivates the ’autoConfig’ function. Certain label reading

parameters are programmed automatically in the setup by the labels

which the BCL 8 reads while the 'autoConfig' function is active.

Parameter

’+’

Activates ’autoConfig’

’/’

Rejects the last code read

’-’

Deactivates ’autoConfig’ and stores the decoded data in the current

parameter set

Acknowledg

ment

’CSx’

Status

’0’ Valid ’CA’ command

’1’ Invalid command

’2’ autoConfig could not be activated

’3’ autoConfig could not be deactivated

’4’ Result could not be deleted

Description

’xx yy zzzzzz’

Code type of the read code

’01’ 2/5 Interleaved

’02’ Code 39

’06’ UPC (A, E)

’07’ EAN

’08’ Code 128, EAN 128

’09’ Pharmacode

’10’ EAN/UPC

’11’ Codabar

’12’ Code 93

No. of digits of the read code

zzzzzz Contents of the decoded label. The



appears if the label was not

correctly read.

UM_BCL8_de_50040581.book Seite 60 Montag, 24. Februar 2020 9:53 09

Содержание 50038948











































































Результаты поиска

Содержание 50038948

Отзывы:

Бренды по названию

Популярные бренды

Leuze electronic 50038948, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50038948

Отзывы:

Бренды по названию

Популярные бренды