manualshive.com logo in svg

Leuze electronic 50038948, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Leuze electronic 50038948 Скачать руководство пользователя страница 26

Accessories/order codes

24

BCL 8

Leuze electronic

Connecting the switching input / switching output

The MA 8.1 is provided with a switching input and a switching output. The connection of

switching input / switching output is carried out in accordance with Figure 5.2.

Figure 5.2: Connection of the switching input/output of the MA 8.1

NOTE

The  switching  input/switching  output  are  programmed  via  the  BCLconfig  configuration

software. For more information, see also chapter 10.6 and chapter 10.8, page 59 et seq.

 

ATTENTION!

If you use a sensor with a standard M12 connector, then please note the following:

Use only sensors on which the switching output does not lie on pin 2 or sensor cables 

on which pin 2 is not assigned. Otherwise, the switching output is not protected against 

feedback on the switching input. If the inverted sensor output lies on pin 2, erroneous 

behavior of the switching output will result.

Switching input

Switching output

UM_BCL8_de_50040581.book  Seite 24  Montag, 24. Februar 2020  9:53 09

Содержание 50038948











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды