Let's Go Aero GearSpace HGK963 Скачать руководство пользователя страница 5

PAGE 5 OF 5

The bicycle fork mount is a standard bicycle Fork mount/Skewer system intended for most styles bicycles. 

Consult your bicycle manual to confirm compatibility of the GearSpace bike mount.

Prepare your bicycle for mounting by removing the bicycles front tire exposing the bicycles’ “Fork” (refer to 

your Bicycles Manual for proper tire removal).

Loosen the 

Tension Nut

 located on the Forks’ 

Skewer

 and confirm the 

Quick Release Arm

 is in the “Open” 

position [Figure 17]. Lower your bicycles fork onto the 

Skewer

 and secure your bicycle by tighten the 

Tension 

Nut

 and moving the 

Quick Release Arm

 to the “Closed” position [Figure 18]. 

Stretch and connect the remaining hook on the Adjustable Bungee [

M

] to the frame of the bicycle. 

OPERATION & BIKE INSTALLATION:

To Avoid Personal Injury or Damage and Loss To Your 

Bicycle and/or Carrier, All Hardware And Connections 

Must Be Fully Secured Before Transit.

Before Transit: Confirm The Fork Mount Skewer Is In The 

“CLOSED POSITION” And The Bicycle Is Properly Secured 

To Avoid Loss And Damage To The Carrier And/Or Bicycle Or 

Personal Injury.

      WARNING: 

[Figure 17]

[Figure 18]

      WARNING: 

ONE YEAR LIMITED WARRANTY

We warrant this Let’s Go Aero brand product during the time the original retail purchaser owns it. This warranty terminates if a purchaser 

transfers the product to any other person.

Let’s Go Aero warrants this product to be free from defect in material and workmanship for one year (retain your sales receipt for your 

records). Any product or part thereof found to be defective within that period will be replaced without charge provided that: (1) the product was 

not misused; (2) no alterations or modifications were made; (3) its failure was not a result of normal wear expected in the use of the product; 

(4) the product or part is delivered, freight prepaid, to Let’s Go Aero.

 

Manufacturers only obligation shall be to replace such products or parts proved to be defective. A Return Merchandise Authorization is 

required prior to return. Please contact Let’s Go Aero toll-free, at 877-464-2376 or 719-630-3800, or via email to [email protected] to 

get an RMA number.

No warranty is given for LGA products purchased outside of the United States and Canada.

© Copyright 2018

BICYCLE FORK

TENSION

NUT

SKEWER

OPEN POSITION

QUICK RELEASE 

BICYCLE FORK

TENSION

NUT

CLOSED POSITION

QUICK RELEASE 

Содержание GearSpace HGK963






Отзывы: