background image

FCC Notice

 

This  equipment  has  been  tested  and found to  comply  with  the  limits  for  a  Class-A  digital device, 
pursuant  to  Part  15  of  the  FCC  rules.  These  limits  are  designed  to  provide  reasonable  protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy. It may cause harmful interference  to radio communications if the 
equipment  is  not  installed  and  used  in  accordance  with  the  instructions.  However,  there  is  no 
guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by  turning  the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of 
the following measures:

 

 

Reorient or relocate the receiving antenna.

 

 

Increase the separation between the equipment and receiver.

 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected.

 

 

Consult the dealer or an experienced radio/TV technician for help.

 

 
 

Caution: Any changes or modifications not expressly approved by the grantee of this device could 
void the user's authority to operate the equipment.

 

 
 

CE Mark Warning

 

This is a Class-A product. In a domestic environment this product may cause radio interference in 
which case the user may be required to take adequate measures.

 

 
 

This document is the current official release manual. Please check our website (www.leonton.com) 
for any updated manual or contact us by e-mail ([email protected]).

 

Содержание ET2-0602-M Series


















Отзывы: