background image

 

LMS Operating Manual 

Page 9 

Defaults: 

 

Web 

Setup Administrator 

setupadmin  *this is coded into the firmware and is not editable 

 

Setup Password  

-22718         *use LMS NetworkCode as password 

Web 

List Administrator 

listadmin 

 

List Password   

idoemaillist 

 

Please define: 
LMS:  IP (IP1, IP2, IP3, IP4) 

NetworkCode:  number –30000 to 30000 
Web 

Setup:  Subnet Mask 

 

SMTP Server 

 

 

Gateway 

 

SMTP auth user  

 

DNS Server 

 

SMTP password 

 

Contacts: 

At least 1 email contact 

 
Installation Instructions: 

#1 – Set Your IP 
From the LMS front panel: Tap Menu to ender Edit. 
Tap Test and Menu simultaneously, to switch to the *SETUP* group of parameters. 

Use Step to advance to IP1,IP2,IP3,IP4 and set them accordingly. 
If desired modify your Unit ID and NetworkCode. 

Tap Menu 3 times to advance out of Edit and back to the runtime temperatures. 
Hold Reset until the display goes blank, then release. 

 

#2 -- Define your network and email settings 

Using your web browser enter the IP address to access the unit. 
After reviewing main web page, add "/setup.html" to the IP, to access the Setup Info. 

Name: setupadmin (unchangable, case sensitive)  Passcode: -22718 

Enter your Subnet Mask, Gateway, DNS Server. 

 

Enter your SMTP server, SMTP auth user, and SMTP password. 

Submit. 

Back at the main page verify server and address at top of page, then click "Edit Contact List" 

Name: listadmin    Passcode: idoemaillist 

Please add one contact email address. 
Submit. 

 

 

#3 -- Test 

Back at main page click "Send test email", and wait. 

Click "View Test/Email Failure Log". 

Success:  "Admin Test 1sent" 
Failure: “Admin Test 1fail” 

Check your email for message received 

 
After Daylight Savings Time ends in November, and before it begins in March, please update the Setup 

Parameters DST start and end to ensure proper date/time. 
 

DST Start 

DST End 

Sunday March 13, 2016 

Sunday November 6, 2016 

Sunday March 12, 2017 

Sunday November 5, 2017 

Sunday March 11, 2018 

Sunday November 4, 2018 

Sunday March 10, 2019 

Sunday November 3, 2019 

Sunday March 8, 2020 

Sunday November 1, 2020 

Sunday March 14, 2021 

Sunday November 7, 2021 

Sunday March 13, 2022 

Sunday November 6, 2022 

Содержание LMS-188-4P
















Отзывы: