Lenze E94AYCEO Скачать руководство пользователя страница 76

Страница: 76 / 149

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

Diagnostics

11.1

LED status displays

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Diagnostics

The LEDs on the front of the communication module serve to diagnose faults. Moreover, the

»Engineer« serves to show diagnostic information.

11.1

LED status displays

The following status displays are distinguished:

•

Module status displays

•

•

Status displays on the RJ45 sockets (X233, X234)

(



80)



Note!

LED status displays for trouble-free operation:

• The LEDs

are permanently on.

• The green LEDs on the

X233

and

X234

RJ45 sockets are lit, and the yellow LEDs are

blinking or jittering

(



80)

Содержание E94AYCEO






















































































































































Результаты поиска

Содержание E94AYCEO

Отзывы:

Lenze E94AYCEO, Руководство по связи, Страница: 76 / 149

Результаты поиска

Содержание E94AYCEO

Отзывы: