Lenze E94AYCEO Скачать руководство пользователя страница 67

Страница: 67 / 149

I/O data transfer (implicit messages)

8.4

I/O configuration with »RSLogix 5000« version 20 or higher

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

10. Open the "New Module" dialog window, select the

Connection

tab and set further

properties.

Required settings

Optional settings

Settings

Description

Requested Packet

Interval (RPI)

Set

RPI



2.0 ms

. (Standard: 10 ms)

The RPI [ms] specifies the intervals for the I/O data exchange between the drive

(adapter) and the controller (scanner).

Input type

"Multicast"

input type:

• The input data is sent from the adapter to the scanner by means of multicast

telegrams.

• Other scanners can access this data in addition to the currently configured

scanner ("Listen only" or "Input only" connections).

"Unicast"

input type:

The input data is sent from the adapter to the scanner by means of unicast

telegrams.

Settings

Description

Inhibit module

This option serves to interrupt or inhibit the communication to the adapter.

Major Fault On

Controller If Connection

Fails While In Run Mode

This option serves to put the scanner into the error status if the EtherNet/IP

connection to the drive (adapter) fails while the scanner is in operation.

Содержание E94AYCEO






















































































































































Результаты поиска

Содержание E94AYCEO

Отзывы:

Lenze E94AYCEO, Руководство по связи, Страница: 67 / 149

Результаты поиска

Содержание E94AYCEO

Отзывы: