Lenze E84AYCER Скачать руководство пользователя страница 84

Страница: 84 / 101

Error messages

Possible causes and remedies

Lenze · E84AYCER communication module (PROFINET) · EDS84AYCER EN 3.0 - 02/2019

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

PROFINET: IP address error [0x01bc6533]

PROFINET: Stack init error [0x01bc6534]

PROFINET: Internal error [0x01bc6650]

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

An invalid IP address has been assigned by the I/O cont-

roller via PROFINET or has been set in code

C13000

• Make sure that the I/O controller has assigned a valid

IP address via PROFINET.

• Set a valid IP address.



Setting the IP configuration (



38)

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

The stack cannot be initialised with the parameters se-

lected by the user. This may be due to a station name

which does not comply with the PROFINET specification.

Check and, if necessary, adapt PROFINET parameters:



Setting the IP configuration (



38)



Setting the station name (



36)

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

Internal error

Send communication module together with a descripti-

on of the fault to Lenze.

Содержание E84AYCER






































































































Результаты поиска

Содержание E84AYCER

Отзывы:

Похожие инструкции для E84AYCER

Бренды по названию

Популярные бренды

Lenze E84AYCER, Руководство по связи

Результаты поиска

Содержание E84AYCER

Отзывы:

Похожие инструкции для E84AYCER

Бренды по названию

Популярные бренды