Lenze AC Tech SC Series Скачать руководство пользователя страница 25

Страница: 25 / 32

RG-SFMOD

Drive Control & Communication

AC Tech
Register
Number
(hexadecimal
representation)

Parameter

Parameter Name

Range of Adjustment
Modbus value (decimal value)

Factory Default

65 (41H)

Serial Link

01 - Disable
02 - 9600, 8, N, 2 with Timer
03 - 9600, 8, N, 2, without Timer
04 - 9600, 8, E, 1 with Timer
05 - 9600, 8, E, 1, without Timer
06 - 9600, 8, O, 1 with Timer
07 - 9600, 8, O, 1, without Timer

02 - 9600, N, 2 w/ Timer

66 (42H)

Units Editing

01 - Tenths of Units
02 - Whole Units

02 - Whole Units

67 (43H)

Rotation

01 - Forward Only
02 - Forward and Reverse

01 - Forward Only

Not Used

69 (45H)

Acceleration Time

1 – 36000 (0.1 sec – 3600.0 sec)

200 (20.0 sec)

70 (46H)

Deceleration Time

1 – 36000 (0.1 sec – 3600.0 sec)

200 (20.0 sec)

71 (47H)

DC Brake Time

0 – 36000 (0.0 sec – 3600.0 sec)

0 (0.0 sec)

72 (48H)

DC Brake Voltage

0 – 300 (0.0 - 30.0% of nominal voltage)

0 (0.0%)

73 (49H)

Minimum Frequency

0 - Maximum Frequency (0.0 - 240.0 Hz)

0 (0.0 Hz)

74 (4AH)

Maximum Frequency

Minimum Frequency – 2400 (240.0 Hz)

600 (60.0 Hz)

75 (4BH)

Current Limit

300 - 1800 (30 – 180%)

1800 (180%)

76 (4CH)

Motor Overload

300 - 1000 (30 - 100%)

1000 (100%)

77 (4DH)

Base Frequency

250 - 5000 (25.0 - 500.0 Hz)

600 (60.0 Hz)

78 (4EH)

Fixed Boost

0 – 300 (0.0 - 30.0%)

10 (1.0%)

79 (4FH)

Accel Boost

0 – 200 (0.0 - 20.0%)

0 (0.0%)

80 (50H)

Slip Compensation

0 – 50 (0.0 - 5.0%)

0 (0.0%)

81 (51H)

Preset Speed #1

0 - Maximum Frequency (0.0 - 240.0 Hz)

0 (0.0 Hz)

82 (52H)

Preset Speed #2

0 - Maximum Frequency (0.0 - 240.0 Hz)

0 (0.0 Hz)

83 (53H)

Preset Speed #3

0 - Maximum Frequency (0.0 - 240.0 Hz)

0 (0.0 Hz)

84 (54H)

Preset Speed #4

0 - Maximum Frequency (0.0 - 240.0 Hz)

0 (0.0 Hz)

85 (55H)

Preset Speed #5 /
Skip Frequency #1

0 - Maximum Frequency (0.0 - 240.0 Hz)

0 (0.0 Hz)

86 (56H)

Preset Speed #6 /
Skip Frequency #1

0 - Maximum Frequency (0.0 - 240.0 Hz)

0 (0.0 Hz)

87 (57H)

Preset Speed #7 /
Skip Frequency #2

0 - Maximum Frequency (0.0 - 240.0 Hz)

0 (0.0 Hz)

88 (58H)

Skip Bandwidth

0 - 100 (0.0 - 10.0 Hz)

0 (0.0 Hz)

89 (59H)

Speed Scaling

0 – 65000 (0.0 - 6500.0)

0 (0.0)

90 (5AH)

Frequency Scaling

30 – 20000 (3.0 - 2000 Hz)

600 (60.0 Hz)

91 (5BH)

Load Scaling

100 - 2000 (10 - 200%)

2000 (200%)

= Drive's programming parameter number

Содержание AC Tech SC Series

































Результаты поиска

Содержание AC Tech SC Series

Отзывы:

Похожие инструкции для AC Tech SC Series

Бренды по названию

Популярные бренды

Lenze AC Tech SC Series, Справочное руководство

Результаты поиска

Содержание AC Tech SC Series

Отзывы:

Похожие инструкции для AC Tech SC Series

Бренды по названию

Популярные бренды