Lenovo ThinkStation P500 Скачать руководство пользователя страница 106

Страница: 106 / 232

Message/Symptom

FRU/Action

Computer will

not

perform a Wake On LAN

(if applicable)

1. Check power supply and signal cable connections

to network adapter.

2. Ensure that the operating system settings are set to

enable Wake on LAN.

3. Ensure Wake On LAN feature is enabled in

Setup/Configuration (see “Starting the Setup Utility
program” on page 65)

4. Ensure network administrator is using correct MAC

address.

5. Ensure no interrupt or I/O address conflicts.

6. Network adapter (advise network administrator of

new MAC address)

Dead computer. See “Hard disk drive boot error” on page
96.

1. Power Supply

2. System Board

Diskette drive in-use light remains on or does not light
when drive is active.

1. Diskette Drive

2. System Board

3. Diskette Drive Cable

Blank screen except for flashing cursor.

1. System Board

2. Primary Hard Disk Drive

3. Hard Disk Drive Cable

Incorrect memory size during POST

1. Run the Memory tests.

2. Memory Module

3. System Board

"Insert a Diskette" icon appears with a known-good
diagnostics diskette in the first 3.5-inch diskette drive.

1. System Board

2. Diskette Drive Cable

3. Network Adapter

Intensity or color varies from left to right of characters
and color bars

1. Display

2. Video adapter (if present)

3. System Board

No power or fan not running

1. See “Hard disk drive boot error” on page 96.

Non-system disk or disk error-type message with a
known-good diagnostic diskette.

1. Diskette Drive

2. System Board

3. Diskette Drive Cable

Other display symptoms not listed above (including blank
or illegible display)

1. Display

2. System Board

Power-on indicator or hard disk drive in-use light not on,
but computer works correctly

1. Power switch/LED assembly

2. System Board

Printer problems

1. Printer

2. System Board

100

ThinkStation P500 and P700 Hardware Maintenance Manual

Содержание ThinkStation P500









































































































































































































































Результаты поиска

Содержание ThinkStation P500

Отзывы:

Бренды по названию

Популярные бренды

Lenovo ThinkStation P500, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkStation P500

Отзывы:

Бренды по названию

Популярные бренды