Lenovo SI4093 Скачать руководство пользователя страница 50

Страница: 50 / 66

SI4093 System Interconnect Module User’s Guide

Resetting and Restarting the Switch

To activate the new image or images, you must reset the switch. To reset the switch,
complete the following steps:

Log on to the CMM CLI as described in the CMM documentation. If necessary,
obtain the IP address of the CMM from your system administrator.

Set the environment to the bay where you installed the switch. For example:

Execute the

reset

command to restart the switch:

Wait for the POST to complete. This may take up to 2 minutes.

Execute the

info

command for the switch that was just restarted and note the

corresponding level of the firmware for the switch. Confirm that the firmware
build number reflects the correct firmware release. For example:

system>

env -T system:switch[1]

system:switch[1]>

reset

system:switch[1]>

info

...
Boot ROM
Rel date: 01/18/2015
Version: 7.11.0.0
Status: Active
Main application
Rel date: 01/18/2015
Version: 7.11.0.0
Status: Active
Main application
Rel date: 01/18/2015
Version: 7.11.0.0
Status: Inactive

Содержание SI4093



































































Результаты поиска

Содержание SI4093

Отзывы:

Похожие инструкции для SI4093

Бренды по названию

Популярные бренды

Lenovo SI4093, Руководство пользователя

Результаты поиска

Содержание SI4093

Отзывы:

Похожие инструкции для SI4093

Бренды по названию

Популярные бренды