manualshive.com logo in svg

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Lenovo BladeCenter HX5 1909 - Проблема Определения И Служебное Руководство для скачивания бесплатно. Это руководство предоставляет важные сведения о разрешении проблем и обслуживании продукта. Скачайте его с manualshive.com и получите доступ к подробной информации о вашем устройстве.

Поделиться
Скачать
background image

•  See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which 

components are FRUs.

•  If an action step is preceded by “(Trained service technician only),” that step must be performed only by a 

trained service technician.

Symptom

Action

One or more blade servers are 
unable to communicate with 
the network.

1.  Check the function of the shared BladeCenter chassis resources. See “Solving 

shared BladeCenter resource problems” on page 269).

2.  Make sure that:  

•  The correct device drivers are installed. See “Updating firmware and device 

drivers” on page 30.

•  Optional I/O-expansion cards are correctly installed and configured. See 

“Installing an I/O expansion card” on page 121 and Chapter 2 “Configuring 
the blade server” on page 19.

3.  (Trained service technician only) Replace the system-board assembly. See 

“Removing the system-board assembly - BladeCenter HX5” on page 140 and 
“Installing the system-board assembly - BladeCenter HX5” on page 142.

An error message "Loading 
Java Applet failed" displays 
when trying to establish a 
remote control console session 
to a blade server. 

Refer to the 

BladeCenter Advanced Management Module User's Guide 

for 

information pertaining to the proper installation and configuration of Java, operating 
systems, and browsers that are supported for remote access.

Operating system problems

Use this information to diagnose operating system problems.

IBM continually updates the support website with tips and techniques that you can use to resolve any 
problems that you might be having with the BladeCenter HX5 blade server. Go to the BladeCenter support 
search website at http://www.ibm.com/systems/support/supportsite.wss/search?brandind=5000020 to see 
if any service bulletins have been generated. In the Search field, enter the following terms: 7872, retain, and 
operating system. 

The following table lists problem symptoms and suggested solutions.

Symptom

Action

The RAID configuration 
program cannot view all 
installed drives, or the 
operating system cannot be 
installed.

•  Make sure that there are no duplicate SCSI/SAS IDs or interrupt request (IRQ) 

assignments. See “Using the LSI Logic Configuration Utility program” on page 29.

•  Make sure that the storage drive is connected correctly. See “Blade server 

connectors - BladeCenter HX5” on page 12 to locate the storage drive connector.

The operating-system 
installation program 
continuously loops.

Make more space available on the hard disk. 

The operating system cannot 
be installed; the option is 
unavailable.

Make sure that the operating system is supported on the blade server. If the 
operating system is supported, either no logical drive is defined (SCSI/SAS RAID 
systems) or the ServerGuide System Partition is not present. Run the ServerGuide 
program and make sure that setup is complete.

Optional-device problems

Use this information to diagnose and resolve optional-device problems.

260

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Patton electronics 3120 Administrator'S Reference Manual preview
3120
Бренд: Patton electronics Страницы: 331
Point Six Link Manager 4010-43 Manual preview
Link Manager 4010-43
Бренд: Point Six Страницы: 131
SafeNet Luna SA Configuration Manual preview
Luna SA
Бренд: SafeNet Страницы: 109
IBM totalstorage 200 Service Manual preview
totalstorage 200
Бренд: IBM Страницы: 180
Lanner LEC-3010 User Manual preview
LEC-3010
Бренд: Lanner Страницы: 43
HPE 3PAR StoreServ Service And Upgrade Manual preview
3PAR StoreServ
Бренд: HPE Страницы: 174
AXIOMTEK NA-1301 Hardware Installation Manual preview
NA-1301
Бренд: AXIOMTEK Страницы: 55
Sun Oracle SPARC T3-2 Service Manual preview
SPARC T3-2
Бренд: Sun Oracle Страницы: 222
Silex technology PRICOM PRICOM C- 5100 User Manual preview
PRICOM PRICOM C- 5100
Бренд: Silex technology Страницы: 7
QNAP TS-401T Turbo Server Quick Installation Manual preview
TS-401T Turbo Server
Бренд: QNAP Страницы: 8
Zycoo IAS-L100 Manual preview
IAS-L100
Бренд: Zycoo Страницы: 36
Oce Repro Desk User Manual preview
Repro Desk
Бренд: Oce Страницы: 464
Black Box LES424A Quick Start Manual preview
LES424A
Бренд: Black Box Страницы: 2
TAG SV-4102-X214 Operation Manual preview
SV-4102-X214
Бренд: TAG Страницы: 50
Intel SE7520AF2 Operating Manual preview
SE7520AF2
Бренд: Intel Страницы: 34
Intel S875WP1-E Specification preview
S875WP1-E
Бренд: Intel Страницы: 117
Nestar PLAN 4000 Installation And Operation Manual preview
PLAN 4000
Бренд: Nestar Страницы: 137
Uniwide AR3016G Hardware User'S Manual preview
AR3016G
Бренд: Uniwide Страницы: 96

Бренды по названию

Популярные бренды

Загрузить еще бренды