Lenovo 70AL Скачать руководство пользователя страница 144

Страница: 144 / 190

7. Position the new front system fan 1 on the system fan 1 mounting area of the chassis so that the

three tips

on the bottom of the front system fan 1 are aligned with the corresponding holes in the

mounting area. Meanwhile, ensure that the two posts

of the front system fan 1 are aligned with the

corresponding holes in the inner side of the chassis. Then, carefully slide the front system fan 1 into
the chassis until it snaps into position.

Figure 85. Installing the front system fan 1

8. Connect the new front system fan 1 cable to the system fan 1 connector on the system board. See

“System board components” on page 38.

9. If you are instructed to return the old front system fan 1, follow all packaging instructions and use any

packaging materials that are supplied to you for shipping.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the replacement, go to “Completing the parts replacement” on page 149.

Replacing the rear system fan

Attention:

Do not open your server or attempt any repair before reading and understanding “Safety information”

on page iii and “Guidelines” on page 65.

This topic provides instructions on how to replace the rear system fan.

132

ThinkServer TS440 Hardware Maintenance Manual

Содержание 70AL































































































































































































Результаты поиска

Содержание 70AL

Отзывы:

Lenovo 70AL, Руководство по обслуживанию, Страница: 144 / 190

Результаты поиска

Содержание 70AL

Отзывы: