manualshive.com logo in svg

Lenovo 3000K, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo 3000K Скачать руководство пользователя страница 43

Chapter 7. Replacing hardware

      41

connector   at the rear of the computer or to a USB connector   
at either the front or rear of the computer.

4.  Disconnect the failing keyboard cable from the computer and connect 

the new keyboard cable to the same connector. 

5.  Refer to the “Completing the installation”.

Replacing the mouse 

Attention

Do not remove the computer cover or attempt any repair before 
reading the “Safety information” .

To replace the mouse: 

1.  Remove any media (diskettes, CDs, or tapes) from the drives, shut 

down your operating system, and turn off all attached devices and the 
computer. 

2.  Unplug all power cords from electrical outlets. 
3.  Locate the connector for the mouse.

Note: 

Your mouse might be connected to the standard mouse 

connector   at the rear of the computer or to a USB connector   
at either the front or rear of the computer. 

4.  Disconnect the failing mouse cable from the computer. 
5.  Connect the new mouse cable to the connector. 
6.  Refer to the “Completing the installation.” 

Содержание 3000K


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды