manualshive.com logo in svg

Lenovo 3000K, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo 3000K Скачать руководство пользователя страница 33

Chapter 7. Replacing hardware

      31

3.  Remove the four screws that secure the power supply at the rear of the 

chassis. 

4.  Lift the power supply out of the chassis. 
5.  Install the new power supply into the chassis so that the screw holes in 

the power supply align with those in the chassis. 

6.  Install the four screws to secure the power supply. Note: Use only the 

screws provided by Lenovo. 

7.  Reconnect the power supply connectors to the system board. 
8.  Reconnect a power supply connector to each of the drives. 
9.  Refer to the “Completing the installation”.

Replacing the heat sink assembly 

Attention

Do not remove the computer cover or attempt any repair before 
reading the “Safety information” . 

To replace the heat sink assembly: 

1.  Remove the computer cover. Refer to “Removing the computer cover”. 
2.  Lay the computer on its side. 
3.  Locate the heat sink. 
4.  Disconnect the heat sink and the fan assembly cable from the system 

Содержание 3000K


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды