Lennox RGEN30 Скачать руководство пользователя страница 3

XP-6341 6/10

3

Safety Precautions and Instructions

Safety Precautions and Instructions

IMPORTANT SAFETY INSTRUCTIONS.

Electromechanical

equipment,

including

generator

sets,

transfer

switches, switchgear, and accessories,
can cause bodily harm and pose
life-threatening

danger

when

improperly

installed,

operated,

or

maintained. To prevent accidents be
aware of potential dangers and act
safely.

Read and follow all safety

precautions and instructions.

SAVE

THESE INSTRUCTIONS.

This manual has several types of safety
precautions and instructions: Danger,
Warning, Caution, and Notice.

DANGER

Danger indicates the presence of a
hazard

that

will

cause

severe

personal

injury,

death

,

or

substantial property damage

.

WARNING

Warning indicates the presence of a
hazard

that

can

cause

severe

personal

injury,

death,

or

substantial property damage

.

CAUTION

Caution indicates the presence of a
hazard that

will

or

can cause minor

personal injury

or

property damage

.

NOTICE

Notice

communicates

installation,

operation, or maintenance information
that is safety related but not hazard
related.

Safety decals affixed to the equipment
in prominent places alert the operator
or service technician to potential
hazards and explain how to act safely.
The decals are shown throughout this
publication

to

improve

operator

recognition.

Replace missing or

damaged decals.

Accidental Starting

Accidental starting.
Can cause severe injury or death.

Disconnect the battery cables before
working

on

the

generator

set.

Remove the negative (--) lead first
when

disconnecting

the

battery.

Reconnect the negative (--) lead last
when reconnecting the battery.

WARNING

Disabling

the

generator

set.

Accidental

starting

can

cause

severe injury or death.

Before

working on the generator set or
connected equipment, disable the
generator set as follows: (1) Move the
generator set master switch to the OFF
position. (2) Disconnect the power to
the battery charger. (3) Remove the
battery cables, negative (--) lead first.
Reconnect the negative (--) lead last
when reconnecting the battery. Follow
these precautions to prevent starting of
the generator set by an automatic
transfer

switch,

remote

start/stop

switch, or engine start command from a
remote computer.

Battery

Sulfuric acid in batteries.
Can cause severe injury or death.

Wear

protective

goggles

and

clothing.

Battery acid may cause

blindness and burn skin.

WARNING

Explosion.
Can cause severe injury or death.
Relays in the battery charger
cause arcs or sparks.

Locate the battery in a well-ventilated
area. Isolate the battery charger from
explosive fumes.

WARNING

Battery gases. Explosion can cause
severe injury or death.

Battery gases

can cause an explosion. Do not smoke
or permit flames or sparks to occur near
a battery at any time, particularly when
it is charging.

Do not dispose of a

battery in a fire. To prevent burns and
sparks that could cause an explosion,
avoid touching the battery terminals
with tools or other metal objects.
Remove all jewelry before servicing the
equipment. Discharge static electricity
from

your

body

before

touching

batteries by first touching a grounded
metal surface away from the battery. To
avoid sparks, do not disturb the battery
charger connections while the battery
is charging. Always turn the battery
charger off before disconnecting the
battery connections.

Ventilate the

compartments containing batteries to
prevent accumulation of explosive
gases.

Battery

electrolyte

is

a diluted

sulfuric acid. Battery acid can cause
severe injury or death.

Battery acid

can cause blindness and burn skin.
Always

wear

splashproof

safety

goggles, rubber gloves, and boots
when servicing the battery.

Do not

open a sealed battery or mutilate the
battery case. If battery acid splashes in
the eyes or on the skin, immediately
flush the affected area for 15 minutes
with large quantities of clean water.
Seek immediate medical aid in the case
of eye contact. Never add acid to a
battery after placing the battery in
service, as this may result in hazardous
spattering of battery acid.

Содержание RGEN30





















































Отзывы: