manualshive.com logo in svg

Lennox RGEN30, Руководство по установке

Поделиться
Скачать
Lennox RGEN30 Скачать руководство пользователя страница 20

XP-6341 6/10

20

Section 2 Installation Instructions

LP Fuel Conversion Procedure

Use the following steps to convert the fuel system to LP
gas, if necessary:

1. Remove the fuel regulator cover plug.

See

Figure 2-11.

2. Remove the adjustment screw and spring from the

fuel regulator.

Save the adjustment screw and

spring for possible conversion back to natural gas.

3. Reinstall the cover plug.

4. Rotate the regulator to point down as shown in

Figure 2-7.

5. Disconnect leads 65 and 70A at the quick connects

in the wiring harness. See Figure 2-10.

6. Proceed to Section 2.2.10 to check and adjust the

fuel supply pressure.

Natural Gas Fuel Conversion Procedure

Use the following steps to convert the generator set to
natural gas, if necessary:

1. Rotate the regulator so that it is pointing up.

2. Remove the fuel regulator cover plug.

See

Figure 2-11.

SB-527

1. Fuel regulator
2. Spring

3. Adjustment screw
4. Cover plug

1

2

3

4

Figure 2-11

Fuel Regulator

3. Install the spring and adjustment screw.

4. Adjust the screw 11.1 mm (7/16 in.) down from the

top of the regulator.

5. Reinstall the cover plug.

6. Connect leads 65 and 70A at the quick-connects in

the wiring harness. See Figure 2-10.

Содержание RGEN30





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды