Lennox RGEN30 Скачать руководство пользователя страница 17

XP-6341 6/10

17

Section 2 Installation Instructions

6. Connect the red battery cable to the positive (+)

battery terminal.

7. Connect the black battery cable to the negative (--)

battery terminal.

8. Place the boots over the battery terminals.

9. Plug the battery charger into the 120 VAC power

supply.

2.2.5

Install and Connect Fuel Supply

Explosive fuel vapors.
Can cause severe injury or death.

Use extreme care when handling,
storing, and using fuels.

WARNING

The fuel system. Explosive fuel vapors can cause severe
injury or death.

Vaporized fuels are highly explosive. Use

extreme care when handling and storing fuels. Store fuels in a
well-ventilated area away from spark-producing equipment
and out of the reach of children. Never add fuel to the tank
while the engine is running because spilled fuel may ignite on
contact with hot parts or from sparks. Do not smoke or permit
flames or sparks to occur near sources of spilled fuel or fuel
vapors. Keep the fuel lines and connections tight and in good
condition. Do not replace flexible fuel lines with rigid lines. Use
flexible sections to avoid fuel line breakage caused by
vibration. Do not operate the generator set in the presence of
fuel leaks, fuel accumulation, or sparks. Repair fuel systems
before resuming generator set operation.

Note:

Have the fuel piping and regulator installed by the
fuel supplier. The fuel supply installation must
comply with NFPA and local codes.

1. See Figure 2-2, Figure 2-3, and Figure 2-4 for the

fuel supply requirements.

Add up the fuel

requirements for the generator set plus all other
gas-fired equipment fueled by the same supply.

2. Check that the primary regulator and gas meter

have sufficient capacity for the fuel requirements
for the generator set plus all other gas-fired
equipment. Have the fuel supplier install a larger
gas meter, if necessary.

Model

Gas Flow Rate, Btu/hr.

RGEN30

450000

Figure 2-2

Gas Flow Rate (natural gas and LP)

Fuel Supply Specifications

Fuel type

LP Gas or Natural

Gas

Fuel supply inlet

3/4-14 NPT

Fuel supply pressure,
oz./in.

2

(in. H

2

O)

4--6 (7--11)

Nominal Fuel Rating, Btu/ft.

3

:

Natural gas

1000

LP vapor

2500

Figure 2-3

Fuel Requirements

Fuel Consumption

m

3

/hr. (cfh)

Natural Gas at % Load

100%

12.7

(450)

75%

10.6

(375)

50%

8.5

(300)

25%

6.4

(225)

LP Gas at % Load

100%

5.1

(180)

75%

4.2

(150)

50%

3.4

(120)

25%

2.5

(90)

Figure 2-4

Fuel Consumption

3. Measure the pipe length from the primary gas

pressure regulator to the pipe connection on the
generator set fuel inlet. Add 2.4 m (8 ft.) to the
measured length for each 90 degree elbow. Use
the pipe size indicated in Figure 2-5 for the total
length of pipe.

Maximum Pipe Length m (ft.)

Pipe Size

6.1

(20)

1 1/4 in. NPT

9.1

(30)

1 1/4 in. NPT

18.3

(60)

1 1/2 in. NPT

30.5

(100)

1 1/2 in. NPT

45.7

(150)

2 in. NPT

61.0

(200)

2 in. NPT

Figure 2-5

Fuel Pipe Sizes

Содержание RGEN30





















































Отзывы: