Lennox Merit Plus MPD35PF-NE-B Скачать руководство пользователя страница 1

Страница: 1 / 40

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

This appliance may be installed in an aftermarket

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes. This appliance is only for use with

the type of gas indicated on the rating plate. This

appliance is not convertible for use with other

gases, unless a certified kit is used.

In the Commonwealth of Massachusetts:

•

Installation must be performed by a licensed plumber or

gas fitter;

• See Table of Contents for location of additional Com-

monwealth of Massachusetts requirements.

Portland

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

INSTALLATEUR: Laissez cette notice avec l'appareil.

CONSOMMATEUR: Conservez cette notice pour con-

sultation ultérieure.

WARNING: IF THE INFORMATION IN THIS MANUAL

IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-

SION MAY RESULT CAUSING PROPERTY DAMAGE,

PERSONAL INJURY OR LOSS OF LIFE.

Do not store or use gasoline or other flammable

vapors or liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow your gas supplier's

instructions.

• If your gas supplier cannot be reached, call

the fire department.

Installation and service must be performed by

a qualified installer, service agency or the gas

supplier

AVERTISSEMENT: ASSUREZ-VOUS DE BIEN

SUIVRE LES INSTRUCTIONS DONNÉES DANS

CETTE NOTICE POUR RÉDUIRE AU MINIMUM LE

RISQUE D'INCENDIE D'EXPLOSION OU POUR

ÉVITER TOUT DOMMAGE MATÉRIEL, TOUTE

BLESSURE OU LA MORT.

Ne pas entreposer ni utiliser d'essence ni d'autre

vapeurs ou liquides inflammables dans le voisinage

de cet appareil ou de tout autre appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE

GAZ:

• Ne pas tenter d'allumer d'appareil.

• Ne touchez à aucun interrupteur. Ne pas vous

servir des téléphones se trouvant dans le báti-

ment où vous vous trouvez.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions

du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de

gaz, appelez le service des incendies.

L'installation et l'entretien doivent être assurés

par un installeur ou un service d'entretien qualifié

ou par le fournisseur de gaz.

INSTALLATION

INSTRUCTIONS

MPD35ST-NM-B

MPD35ST-NE-B

MPD35ST-PM-B

MPD35PF-NE-B

MPD35PF-NM-B

MPD35PF-PM-B

Millivolt Models

Electronic Models

MODELS

P/N 850,024M REV. F 06/2009

DIRECT VENT GAS FIREPLACE HEATERS

A French manual is available upon request. Order P/N 850,024CF
Ce manuel d’installation est disponible en francais, simplement en

faire la demande. Numéro de la pièce 850,024CF.

DIRECT VENT MULTI-OPEN

MERIT

™

PLUS SERIES

OTL Report No. 6-F-28-5

Содержание Merit Plus MPD35PF-NE-B









































Результаты поиска

Содержание Merit Plus MPD35PF-NE-B

Отзывы:

Похожие инструкции для Merit Plus MPD35PF-NE-B

Бренды по названию

Популярные бренды

Lennox Merit Plus MPD35PF-NE-B, Руководство по установке

Результаты поиска

Содержание Merit Plus MPD35PF-NE-B

Отзывы:

Похожие инструкции для Merit Plus MPD35PF-NE-B

Бренды по названию

Популярные бренды