background image

Page 12

14ACX SERIES

STEP 4 -- ELECTRICAL (CONTINUED) -- High Voltage and Field Control Wiring

The following illustration provide an example of control wiring connections when using standard thermostat.

Any excess high voltage field wiring should be
trimmed and secured away from any low voltage field
wiring. To facilitate a conduit, a cutout is located in the
bottom of the control panel. Connect conduit to the
control panel using a proper conduit fitting.

NOTE

 - Wire tie provides low voltage control wire strain

relief and maintains separation of field-installed low and
high voltage circuits.

NOTE

 - For proper voltages, select thermostat wire

(control wires) gauge per table above

.

NOTE

 - Do not bundle any excess 24VAC control

wires inside control panel.

Install low voltage wiring from outdoor to indoor unit
and from thermostat to indoor unit as illustrated.

A -

Run 24VAC control wires through hole with grommet
and secure with provided wire tie.

B -

Make 24VAC thermostat wire connections. Locate
the two wires from the contactor and make
connection using field-provided wire nuts:

Yellow to Y1

Black to C (common)

ROUTING HIGH VOLTAGE, GROUND AND CONTROL WIRING

WIRE RUN LENGTH

AWG#   INSULATION TYPE

LESS THAN 100' (30 METERS)

18      TEMPERATURE RATING

MORE THAN 100' (30 METERS) 16       35ºC MINIMUM.

HIGH VOLTAGE / GROUND WIRES

FIELD CONTROL WIRING

W1

Y

G

C

R

Y

G

C

THERMOSTAT

INDOOR UNIT

POWER

HEAT

COOLING

INDOOR BLOWER

COMMON

OUTDOOR UNIT

Y1

C

W

R

YELLOW

BLACK

FIGURE 13

NOTE

 - Refer to furnace, blower coil and accessory instructions for

additional wiring configurations with other optional controls.

14ACX

24VAC Control Wiring Diagrams (Field Installed)

14ACX

14ACX

14ACX

14ACX

14ACX

14ACX

ML180

EL280, EL295, EL296

SLP98, SL28UH, SL280DF

CBX25

CBX40UHV

BROWN

BLUE

RED

1

2

3

1

2

3

Air handler shipped with jumpers installed between W1 and W2
and W2 and W3.

R connection required for air conditioner with LSOM. Resistor kit
(CAT #47W97) required when connection ComfortSense 7000
with LSOM 2.

L connection wired on units with LSOM.

FIGURE 14

Содержание Merit 14ACX-018-230

















Отзывы: