Lennox LI009HI-380P432, Руководство пользователя

Страница: 25 / 36

22
■
■
Installation notice
■
■
■
7
■
■
8
3
12
9
4
5
13
6
■
14
10
WARNING
11
Screw driver
Impact drill
To ensure safety, please be mindful of the
following precautions.
Pipe cutter
Open-end
detector
wrench
Vacuum pump
Leakage
Pressure meter
tape
Measuring
Le v e l meter
meter
s pa nne r
U niv er s a l
I nn er h exa g o n
Drill head
NOTICE
●
●
Electric wires with insufficient capacity, wrong
wire connections and insecure wire terminals
may cause electric shock or fire.
P i pe ex pand er
Torq u e wr en c h
P l ea s e co n tact t h e l oca l a g e n t f or ins ta ll at i o n.
Do n ’t us e un q u a lifi e d power co ld.
1 minute.
When refrigerant needs to be recovered
during relocating or repairing the unit, be
Tools for installation
1 8
Safety precautions for installing and
relocating the unit
When installing the unit, make sure that co-
nnection pipe is securely connected before
the compressor starts running.
I f compre ss or s tart s r unning w h e n s top v a lv e
is ope n a nd co nn ect i o n p i pe is n ot y et co nne-
cte d, a i r w ill b e su cke d in a nd ca us e pre ssur e
r ise or compre ss or r u pt u re , re sul t ing in in j u r y.
When installing or relocating the unit, be s-
ure to keep the refrigerant circuit free from
air or substances other than the specified
refrigerant.
A ny pre s e n ce o f a i r or ot h er f o reign subs ta n ce
in t h e re f r ig er an t c i rc ui t w ill ca us e system pre-
ssu re r is e or compre ss or r u pt u re , re sul t ing
in in j u r y.
When in stalling or moving this unit, do not
charge the refrigerant which is not comply
with that on the nameplate or unqualified
refrigerant.
Otherwise, it may cause abnormal operation,
wro ng act i o n, mec h a ni ca l ma lfun ct i o n or e v e n
seri o us s a f et y acciden t .
WARNING
sure that the unit is running in cooling mode.
Then, fully close the valve at high pressure
side (liquid valve). About 30-40 seconds later,
fully close the valve at low pressure side
(gas valve), immediately stop the unit and
disconnect power. Please note that the time
for refrigerant recovery should not exceed
Use the specified types of wires for electrical
connections between the indoor and outdoor
units. Firmly clamp the wires so that their te-
rminals receive no external stresses.
Prohibit installing the unit at the place where
there may be leaked corrosive gas or flamm-
able gas.
If there is leaked gas around the unit, it may
ca use explosi o d n a n ot her acc id e n t s.
Do not use extension cords for electrical co-
nnections. If the electric wire is not long eno-
ugh, please contact a local service center au-
At least 15cm
At least 250cm
e ceiling
Space to the wall
15cm
At least 15cm
thorized and ask for a proper electric wire.
Poor co nn ect i o ns ma y l ea d to e l ectr i c sh ock or fi re .
Space to the wall
At
Space to th
least
At least 300cm
Space to the obstruction
Space to the floor
I f re f r ig er an t reco v er y take s too m u c h t i me ,
a i r ma y b e su cke d in a nd ca us e pr essur e
r is e or compre ss or ru pt u re , re sul t ing in in j ury.
During refrigerant recovery, make sure that
liquid valve and gas valve are fully closed
and power is disconnected before detachi-
ng the connection pipe.
I f co mpress or s tart s r unning w h e n s top valv e
is ope n a nd co nn ect i o n p i pe is n ot y et co nn-
ecte d, a i r w ill b e su cke d in a nd ca us e pre ssu re
r is e or compre ss or r u pt u re , re sul t ing in in j u r y.
50cm
Above
Space to the wall
m
Above
Air inlet side
Space to the obstruction
Air outlet side
2
0 00
0
c
30cm
Above
bove
m A
30c
Space to the wall
Drainage pipe
Above
50cm