background image

24

You may avoid inconvenience and service calls by checking these points before you call for service:

IF YOUR SYSTEM IS NOT HEATING OR NOT GIVING ENOUGH HEAT . . .

POSSIBLE CAUSE

WHAT TO DO

Thermostat is not set correctly

Reset thermostat

Burner is not operating properly

Check 

fl

 ame. If it is yellow, the burner is not getting enough air. Or, if 

fl

 ame is blue and noisy and seems to lift off the burner, the burner is 

getting too much air. Contact your service agency.

No electric power to boiler 

Check over-current protection. Check to be sure electric power supply 

circuit is “ON”.

Controls out of  adjustment 

Reset according to instructions.

Radiators not heating

Open radiator vents to excess air. Check 

fl

 ow control valve (if used). It 

may be in closed position.

Circulating pump not running

Check over-current protection. Check relay operation.

Poor electrical contact

Check all control terminals and wire joints.

Chimney 

fl

 ue is blocked

Pressure switch will not close and pilot spark will not operate to  start 

pilot. Have your service technician check and correct, if necessary.

Rollout switch blown

Have your service technician check heat exchanger for blockage. Replace 

rollout switch with exact replacement.

IF BURNER IS NOISY . . . 

POSSIBLE CAUSE

WHAT TO DO

Gas input amount is incorrect

Contact your service technician.

RELIEF VALVE LEAKING . . .

POSSIBLE CAUSE

WHAT TO DO

Dirt on seat 

Open valve manually. Allow water to run and clear valve seat.

Water logged expansion tank

Drain tank, see manufacurer instructions.

HAVE YOUR SERVICE AGENCY CHECK ANY PROBLEM YOU 

ARE UNABLE TO CORRECT.

SERVICE HINTS

CAUTION

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use 

any phone in your building.

• Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions. 

• If you cannot reach your gas supplier, call the 

fi

 re 

department.

!

!

  

Содержание GWB8-042IE-2

































Отзывы: