background image

Page 38

PROBLEM 5: UNIT FAILS TO FIRE IN THE HEATING MODE, COMBUSTION AIR BLOWER

 ENERGIZES, IGNITOR IS ENERGIZED.

Condition

Possible Cause

Corrective Action/Comments

5.1

 − Unit operates with a cooling and
continuous fan demand.

Combustion air inducer energizes

5.1.1

Check that gas is being supplied to

the unit.

ACTION 1 − 

Check line pressure at the gas valve.

Pressure should not exceed 13" WC for both nat-
ural and propane. Line pressure should read a
minimum 4.5" WC for natural and 8.0"WC for pro-
pane.

 − Combustion air inducer energizes
with Heating demand.

 − 

Ignitor is energized but unit fails to

light.

5.1.2

Miswiring of gas valve or loose con-

nections at multi−pin control amp

plugs or valve.

ACTION 1 − 

Check for correct wiring and loose

connections.

 

Correct wiring and/or replace any

loose connections.

LED#1−Alternating Slow Flash
LED#2−Alternating Slow Flash

5.1.3

Defective gas valve or ignition con-

trol.

ACTION 1 − 

Check that 24V is supplied to the gas

valve approximately 35 seconds after heat de-
mand is initiated.

ACTION 2 − 

Replace the valve if 24V is supplied

but valve does not open.

ACTION 3 − 

Replace the control board if 24V is

not supplied to valve.

 PROBLEM 6: BURNERS LIGHT WITH A HEATING DEMAND BUT UNIT SHUTS DOWN

 PREMATURELY

Condition

Possible Cause

Corrective Action/Comments

6.1

 − Burners fire with a heating demand.
 − Burners light but unit shuts off prior
to satisfying T−stat demand.
 − Diagnostic lights flash the pressure
switch code.

LED#1−Off
LED#2−Slow Flash

6.1.1

Low pressure differential at the pres-

sure switch.

ACTION 1 − 

Check for restricted exhaust vent.

Remove all blockage.

ACTION 2:

 Check for proper vent sizing. See

installation instructions.

6.2

 − Combustion air inducer energizes
with a heating demand.

B

li ht b t f il t

t

lit

6.2.1

Sensor or sense wire is improperly

installed.

ACTION 1 −

 Check that sensor is properly lo-

cated and that the sense wire is properly at-
tached to both the sensor and the control.

 − Burners light but fail to stay lit.
 − After 5 tries the control diagnostics
flash the watchguard burners failed to
ignite code.

6.2.2

Sensor or sense wire is broken.

ACTION 1 − 

Check for a broken sensor.

ACTION 2 − 

Test continuity across the sense

wire. If wire or sensor are damaged replace the
component.

ignite code.

LED#1−Alternating Slow Flash
LED#2−Alternating Slow Flash

6.2.3

Sensor or sensor wire is grounded to

the unit.

ACTION 1 − 

Check for resistance between the

sensor rod and the unit ground.

ACTION 2 − 

Check for resistance between the

sensor wire and the unit ground.

ACTION 3 − 

Correct any shorts found in circuit.

6.2.4

Control does not sense flame.

ACTION 1 − 

Check the microamp signal from

the burner flame.

 

If the microamp signal is be-

low 0.23 microamps, check the sense rod for
proper location or contamination.

ACTION 2 − 

Replace, clean, or relocate flame

sense rod. If rod is to be cleaned, use steel
wool or replace sensor. DO NOT CLEAN ROD
WITH SAND PAPER. SAND PAPER WILL
CONTRIBUTE TO THE CONTAMINATION
PROBLEM. 

NOTE: 

Do not attempt to bend

sense rod.

ACTION 3 − 

Check that there is proper ground

to burner box. Repair as necessary.

Содержание G60UHX Series









































Отзывы: