background image

Page 2

LEG DETAIL

BASE

2” (50.8MM) SCH 40

FEMALE THREADED

ADAPTER

ONE BRACKET PER SIDE (MIN.); FOR EXTRA STABILITY, TWO
BRACKETS PER SIDE, 2” (50.8MM) FROM EACH CORNER.

CONCRETE SLAB

 — USE TWO PLASTIC

ANCHORS (HOLE DRILL 1/4”)

COIL

BASE PAN

CORNER POST

STABILIZING BRACKET (18 GAUGE

METAL — 2” WIDTH; HEIGHT AS

REQUIRED)

Slab Side Mounting

#10 1/2” LONG SELF-DRILLING

SHEET METAL SCREWS

#10 1-1/4” LONG HEX HD SCREW

AND FLAT WASHER

MINIMUM ONE

PER SIDE

STABILIZING BRACKET (18 GAUGE METAL
— 2” (50.8MM) WIDTH; HEIGHT AS
REQUIRED); BEND TO FORM RIGHT ANGLE

FOR EXTRA

STABILITY

Deck Top Mounting

Elevated Slab Mounting using Feet

Extenders

Stabilizing Unit on Uneven Surfaces

WOOD OR PLASTIC SLAB

 — NO PLASTIC ANCHOR

(HOLE DRILL 1/8”)

INSTALL UNIT LEVEL OR, IF ON A SLOPE, MAINTAIN SLOPE TOLERANCE
OF 2 DEGREES (OR 2 INCHES PER 5 FEET [50 MM PER 1.5 M]) AWAY
FROM BUILDING STRUCTURE.

MOUNTING
SLAB

BUILDING

STRUCTURE

GROUND LEVEL

Outside Unit Placement

Slab Mounting at Ground Level

SAME FASTENERS AS
SLAB SIDE MOUNTING.

IMPORTANT — 

To help stabilize an outdoor unit, some installations may require strap­

ping the unit to the pad using brackets and anchors commonly available in the market­
place.

DETAIL A

DETAIL B

DETAIL C

DETAIL D

2” (50.8MM) SCH 40

MALE THREADED

ADAPTER

USE ADDITIONAL 2” SCH 40 MALE THREADED ADAPT­
ERS WHICH CAN BE THREADED INTO THE FEMALE
THREADED ADAPTERS TO MAKE ADDITIONAL AD­
JUSTMENTS TO THE LEVEL OF THE UNIT.

TWO 90° ELBOWS INSTALLED IN LINE SET

WILL REDUCE LINE SET VIBRATION.

INSTALL UNIT AWAY FROM WINDOWS

Содержание Dave Lennox Signature XP25

















Отзывы: