background image

INTRODUCTION

This installation and maintenance booklet should always accompany the air treatment unit for ready consultation by
the installer or user if necessary.
The unit should be installed in compliance with the regulations in force in each country and according to the manufacturer's
or qualified person's instructions.
The manufacturer cannot be held liable for any damage to property or injury to persons and animals caused by incorrect
installation of the unit.
Only  qualified  persons  should  install  the  unit  and  connect  it  to  the  mains  electricity  supply.
Before  carrying  out  any  work  on  the  unit,  ensure  that  it  is  disconnected  from  the  electricity  supply.
Read this instruction booklet prior to installation.

RECOMMENDATIONS

This unit is easy to use, but it is important to read all the contents of this guide before using it for the first time. This
will help you to:
- use the unit in all safety
- obtain best performance
- avoid incorrect actions
- respect the environment
Do not allow children or unassisted handicapped persons to use the unit.
Do not touch the unit with wet parts of the body or if barefoot.
Do not tug, pull or twist electrical cables attached to the unit, even when disconnected from the electricity supply.
Do not open the flaps giving access to the internal parts of the unit without having first put the system on-off switch to
"off".
Do not introduce sharp pointed objects through the air intake and outlet grilles.
Do not leave packing material (boards, staples, plastic bags, etc.) within reach of children since they could be a source
of danger. Dispose of correctly.
Do not spray or throw water directly on the unit.
Do not use the unit in places with suspended dust/powder or in potentially explosive atmospheres, in very damp
environments  or  in  the  presence  of  oil  in  suspension  or  in  particularly  aggressive  atmospheres.
Do not cover the unit with objects or drapes that even partially obstruct the air flow.

The unit works by electricity at mains voltage (230 Vac, 50 Hz). Always bear in mind that mains voltage is potentially
dangerous and any appliance connected to it should be used with caution. Before carrying out any work on the unit,
disconnect it from the electricity supply (by pulling out the plug from the mains socket or isolating the supply line by
putting the on-off switch to off).
If the unit is not be used for long periods, make sure that the controls are in the position 0 (off). If the unit is not going
to be used in winter when temperatures are near to freezing, drain the system and ensure that the unit heat exchanger
has no water in it in order to prevent the formation of ice and consequent breakage.
To make the unit inoperable, disconnect it totally from the electricity supply.
It is unsafe to alter or try to alter the characteristics of this product. Any tampering or alteration in any case makes the
warranty null and void.
In the event of malfunction or failure, do not try to repair the unit yourself; contact a qualified technician. Repairs carried
out by incompetent persons could cause damage or accidents.
Always  keep  the  unit  clean.  In  particular  clean  the  air  filter  periodically  (at  least  once  a  month).
.

FAILURE TO COMPLY WITH THE ASSEMBLY INSTRUCTIONS GIVEN IN THIS

GUIDE RELIEVES 

LENNOX 

OF ALL AND ANY LIABILITY. INCORRECT

INSTALLATION COULD CAUSE MALFUNCTIONING OR FAILURE OF THE UNIT.

IT COULD ALSO REPRESENT A HAZARD FOR THE USER.

!

INSTALLATION 

- OPERATING & 

MAINTENANCE

 MANU

A

L

 

Page 

2

 

All manuals and user guides at all-guides.com

Содержание COMFAIR-HH





















Отзывы: