background image

Page 1

©

 2018 Lennox Industries Inc.

CBX25UH (-10)

Service Literature

Corp. 1504-L6

September 2018

INSTALLATION AND SERVICE PROCEDURE

CBX25UH (-10) Series

WARNING

Improper installation, adjustment, alteration, service or
maintenance can cause personal injury, loss of life, or
damage to property.

Installation and service must be performed by a licensed
professional installer (or equivalent) or a service agency.

CAUTION

As with any mechanical equipment, contact with sharp
sheet metal edges can result in personal injury. Take care
while handling this equipment and wear gloves and pro­
tective clothing

.

IMPORTANT

The Clean Air Act of 1990 bans the intentional venting of
refrigerant (CFCs, HCFCs and HFCs) as of July 1, 1992.
Approved methods of recovery, recycling or reclaiming
must be followed. Fines and/or incarceration may be
levied for noncompliance.

Table of Contents

Unit Dimensions 

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications / Electrical Data

3

. . . . . . . . . . . . . . . .

Model Number Information 

4

. . . . . . . . . . . . . . . . . . .

Blower Data

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Application

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unit Components

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Optional ECB25 Electric Heat

7

. . . . . . . . . . . . . . . . .

Configuration Modification

10

. . . . . . . . . . . . . . . . . . .

Electrical Connections

16

. . . . . . . . . . . . . . . . . . . . . .

Wiring Diagrams

18

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Start-Up Operations

20

. . . . . . . . . . . . . . . . . . . . . . . .

Sequence of Operations

21

. . . . . . . . . . . . . . . . . . . .

Performance Checklists

22

. . . . . . . . . . . . . . . . . . . . .

The CBX25UH units are high-efficiency air handlers. Several
models are available in sizes ranging from 1‐1/2 through
5-tons. The CBX25UH is designed for HFC-410A refrigerant.

CBX25UH series units are designed to be matched with either
a 13 SEER air conditioner or heat pump, but can be matched
with other air conditioners or heat pumps as noted in the rating
information. See Product Specification bulletin.
This air handler is designed for indoor installation only. As
shipped, the unit is ready for installation in either upflow or
horizontal left-hand. Field modifications are required for
right-hand air discharge applications. Electric heat, down
flow air discharge application kits, air filters and other
various accessories are available and listed in the

CBX25UH Product Specification bulletin 

for ordering

.

All units come with a factory installed check/expansion
valve.

Information contained in this manual is intended for use by
experienced licensed HVAC service technicians only. All
specifications are subject to change. Procedures outlined in
this manual are presented as a recommendation only and do
not supersede or replace local or state codes.

Содержание CBX25UH 10 Series
























Отзывы: