Lennox Hearth Products RHAP42N Скачать руководство пользователя страница 2

Страница: 2 / 42

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS

PACkAgINg:

Items Packaged with the Fireplace . . . . . . 2

Required Accessories . . . . . . . . . . . . . . . . 2

Optional Accessories . . . . . . . . . . . . . . . . . 2
IMPORTANT WARNINgS/NOTICES . . . . . . . 3
gENERAL INfORMATION:

Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4

Efficiencies . . . . . . . . . . . . . . . . . . . . . . . . 4

Listing Information . . . . . . . . . . . . . . . . . . 4

Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Manufactured Home Requirements . . . . . . 4

Requirements for Commonwealth

of Massachusetts . . . . . . . . . . . . . . . . . . 4

Cold Climate Insulation Requirements . . . 4



TyPICAL INSTALLATION

SEqUENCE/CHECkLIST . . . . . . . . . . . . . . 5
PRE-INSTALLATION STEPS . . . . . . . . . . . . . 5
CLEARANCES. . . . . . . . . . . . . . . . . . . . . . . . 6

Minimum Clearances to Combustibles . . . 6

Recessed Shelf . . . . . . . . . . . . . . . . . . . . . 6

Hearth Extension . . . . . . . . . . . . . . . . . . . 6

Mantels . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Unprotected Side Wall . . . . . . . . . . . . . . . 6

Finish/Surround

(the provided

Fiber Board MUST be installed)

. . . . . . 6

LOCATION ANd fRAMINg:

Location . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Framing the Fireplace . . . . . . . . . . . . . . . . 7

Typical Locations/Installation . . . . . . . . . . 7



Assembling the Top Spacers. . . . . . . . . . 7

Fireplace Dimensions . . . . . . . . . . . . . . . . 8

Fireplace Framing Dimensions . . . . . . . . . 8

Unit Nailing Flanges . . . . . . . . . . . . . . . . . . 9

Ceiling Opening Framing . . . . . . . . . . . . . . 9

Roof Opening Framing . . . . . . . . . . . . . . . 9

Exterior Wall Opening Framing . . . . . . . . . 9
gAS REqUIREMENTS ANd CONNECTION:

General Gas Information and

Important Notices . . . . . . . . . . . . . . . . . 10

Gas Supply Pressure Requirements . . . . 10

Input Rates . . . . . . . . . . . . . . . . . . . . . . . 10

Gas Valve and Test Port Information . . . . 10

Burner Orifice Sizes . . . . . . . . . . . . . . . . . 11

CPI/IPI Switch (Intermittent/Standing

Pilot Modes) . . . . . . . . . . . . . . . . . . . . . 11

Gas Flex-line . . . . . . . . . . . . . . . . . . . . . . 11

Gas-line Shutoff Valve . . . . . . . . . . . . . . . 11

Routing the Gas-line . . . . . . . . . . . . . . . . 12

Control Compartment Access . . . . . . . . . 12

Connecting to the Gas Supply . . . . . . . . . 12

Testing Connections (Factory and Field)

for Gas Leaks . . . . . . . . . . . . . . . . . . . . 12
VENTINg INSTALLATION:

General Information/Important Notices . . 13

Approved Vent Components . . . . . . . . . . 13

Attaching Secure Vent

Components . . . 13

TABLE Of

CONTENTS

ITEMS PACkAgEd

WITH fIREPLACE

• Literature Kit (Installation Instructions

[this manual], Care and Operation

Instructions, Safety-in-Operation

Warnings, Warranty)

• Vent restrictor assembly
• Baffle (shipped on fireplace floor)
• (3) Non-combustible fiber boards
• (3) AAA batteries
• Handheld remote control (transmitter)
• Remote control receiver (wall switch)

assembly with (4) AA batteries

REqUIREd ACCESSORIES*

(Sold separately. See “Accessories” section in

fireplace

Care and Operation Instructions

• Panel Kit (ref. manual 506019-84)
• Floor Kit (ref. manual 506019-84)
• Media Kit (required with DESIGNER style

Floor Kits only; ref. manual 506019-84)

IMPORTANT: Make sure all required

accessory kits are available before

installing fireplace.

___________
*Required for complete fireplace instal la tion.

Refer to the

Rhapsody Linear Required and

Optional Accessories

manual 506019-84

for installation instructions for all required

acces sories.

OPTIONAL ACCESSORIES

(Sold separately. See “Accessories” section in

fireplace

Care and Operation Instructions

• Surround Kit (ref. manual 506019-84)
• Bezel Kit (ref. manual 506019-84)
• Panel Backlighting Kit (ref. manual

506019-84)

• Blower Kit (ref. manual 750028M)
• Power Vent Kit (ref. manual 506022-01)

[Requires Rhapsody Power Vent Adaptor

Kit; manual 506019-82]

• Gas Conversion Kit (ref. manual

506019-90)

PACkAgINg

Firestop/Spacer Requirements

(Vertical and Horizontal) . . . . . . . . . . . . 13

Vent Section Lengths (Nominal/Net) . . . . 14

Telescopic Vent Section . . . . . . . . . . . . . . 14

Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Vent Run Support Requirements . . . . . . . 15

Vent Restrictor Requirements,

Assembly Settings, and Application . . . 16

Using Secure Flex

Kits/Components . . . 17

VERTICAL TERMINATION SySTEMS:

Typical Vertical Termination Systems . . . 18

Vertical Termination System

Rise-to-Run Ratios . . . . . . . . . . . . . . . . 18

Vertical Vent Termination Clearances . . . 19

Installing Vertical Vent Termination . . . . . 19
HORIZONTAL TERMINATION SySTEMS:

Typical Horizontal Termination

Systems . . . . . . . . . . . . . . . . . . . . . . . . 20

Horizontal Termination System

Rise-to-Run Ratios . . . . . . . . . . . . . . . . 20

Horizontal Vent Termination

Clearances . . . . . . . . . . . . . . . . . . . . . . 21

Exterior Horizontal Vent Termination

Clearance Requirements (ANSI/CSA) . . 22

Installing Horizontal Vent Termination . . . 23
fIELd WIRINg:

Field Wiring Steps . . . . . . . . . . . . . . . . . . 24

Wiring Diagram . . . . . . . . . . . . . . . . . . . . 24

Route Fireplace Wiring . . . . . . . . . . . . . . 25

Install/Wire Remote Control system . . . . 26

Install/Wire Optional Power Vent Kit . . . .26

Install/Wire Optional Blower Kit . . . . . . .26

Route Wiring for Optional Panel

Backlighting Kit . . . . . . . . . . . . . . . . . . 26
INSTALLINg fIREPLACE COMPONENTS:

Install Vent Restrictor

(Required with

certain vent runs)

. . . . . . . . . 27 (also 16)

Install Panel Kit (required) . . . . . . . . . . . . 27

Install Panel Backlighting Kit (optional) . . 27

Install Floor Kit (required) and Media

(required with certain Floor Kits) . . . . . 27

Install Baffle (required) . . . . . . . . . . . . . . 27

Installation/Removal of Glass Door . . . . . 28

Installation of Modesty Panel . . . . . . . . . 29

Installation/Removal of Optional Bezel . . 29

Installation of Optional surround . . . . . . . 29
VERIfyINg fIREPLACE OPERATION:

Appliance Checkout . . . . . . . . . . . . . . . . . 30

Lighting Instructions . . . . . . . . . . . . . . . . 31

Adjusting the Air Shutter . . . . . . . . . . . . . 32
fINISH ANd TRIM:

Wall Finish Requirements

for Cleanface Finish . . . . . . . . . . . . 33–34

Wall Finish Requirements when

installing optional Surround

and Bezel . . . . . . . . . . . . . . . . . . . . . 33–34



ATTACHINg SAfETy-IN-OPERATION

WARNINg LABELS. . . . . . . . . . . . . . . . . 35
INSTALLATION ACCESSORIES . . . . . . 36-37

Gas Conversion Kit . . . . . . . . . . . . . . . . . 37
REPLACEMENT PARTS . . . . . . . . . . . . 38–40

Содержание RHAP42N











































Результаты поиска

Содержание RHAP42N

Отзывы:

Бренды по названию

Популярные бренды

Lennox Hearth Products RHAP42N, Руководство по установке

Результаты поиска

Содержание RHAP42N

Отзывы:

Бренды по названию

Популярные бренды