background image

3

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

WARNING:  FAILURE TO COMPLY WITH 
THE INSTALLATION AND OPERATING 
INSTRUCTIONS PROVIDED IN THIS DOCU-
MENT WILL RESULT IN AN IMPROPERLY 
INSTALLED AND OPERATING APPLI-
ANCE, VOIDING ITS WARRANTY.  ANY 
CHANGE TO THIS APPLIANCE AND/OR ITS 
OPERATING CONTROLS IS DANGEROUS.  
IMPROPER INSTALLATION OR USE OF 
THIS APPLIANCE CAN CAUSE SERIOUS 
INJURY OR DEATH FROM FIRE, BURNS, 
EXPLOSION OR CARBON MONOXIDE 
POISONING.

WARNING: CHILDREN AND ADULTS 
SHOULD BE ALERTED TO THE HAZARDS 
OF HIGH SURFACE TEMPERATURES. USE 
CAUTION AROUND THE APPLIANCE TO 
AVOID BURNS OR CLOTHING IGNITION. 
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISED WHEN THEY ARE IN 
THE SAME ROOM AS THE APPLIANCE.

WARNING:  DO NOT PLACE CLOTHING 
OR OTHER FLAMMABLE MATERIALS ON 
OR NEAR THIS APPLIANCE.

AVERTISSEMENT: SURVEILLER LES 
ENFANTS.  GARDER LES VÊTEMENTS, 
LES MEUBLES, L'ESSENCE OU AUTRES 
LIQUIDES À  VAPEUR INFLAMMABLES  À 
COTE DE L'APPAREIL.

Installations at Altitudes of 0 to 4500 feet - 
Units are tested and approved for elevations 
of 0 to 4500 feet (0 to 1370 meters). 

Installations at Altitudes above 4500 ft.- 
For elevations above 4500 feet (1370 
meters), install the unit according to the 
regulations of the local authorities having 
jurisdiction and, in the USA, the latest 
edition of the National Fuel Gas Code (ANSI 
Z223.1) or, in Canada, the  latest edition of 
the CAN-B149.1 and CAN-B149.2 codes.

Table 4 shows the units' gas orifi ce size for 
the elevations indicated:

 

LOCATION

In selecting the location, the aesthetic and 
functional use of the appliance are primary 
concerns. However, vent system routing to 
the exterior and access to the fuel supply are 
also important. Consideration should be given 
to traffi c ways, furniture, draperies, etc., due 
to elevated surface temperatures. 

Considerations Should Include:
• Existing Chimneys
• Aesthetic Considerations
• Roof Design (Rafter Locations & Roof Pitch)
• Room Traffi c
• Proximity to Combustibles
• Proximity for Optimum Heat Transfer
• Electrical Wiring (if optional blower is 
installed)

The installation of this stove will require some 
research. Once your options are determined, 
consult with your local building department 
who will be able to give you the necessary 
installation requirements for your area (Is 
a building permit required?, Rooms where 
installation may not be allowed?, etc.). 

Tables 2 and 3 show the units' gas pressure 
requirements:

Inlet Gas Supply Pressure

(all models)

Fuel #

Minimum

Maximum

Natural Gas

4.5" WC

(1.12 kPa)

10.5" WC

(2.61 kPa)

Propane

11.0" WC

(2.73 kPa)

13.0" WC

(3.23 kPa)

Table 2

Manifold Gas Supply Pressure

(millivolt models)

Fuel #

Low

High

Natural 

Gas

(Lo) 1.6" WC

(.40 kPa)

(Hi) 3.5" WC

(.87 kPa)

Propane

(Lo) 6.3" WC

(1.57 kPa)

(Hi) 10.0" WC

(2.49 kPa)

Table 3

Ne pas se servir de cet appareil s'il a été 
plongé dans l'eau, complètement ou en 
partie.  Appeler un technicien qualifi é pour 
inspecter l'appareil et remplacer toute partie 
du système de contrôle et toute commande 
qui ont été plongés dans l'eau.

This appliance may be installed in an 
aftermarket permanently located, manu-
factured  home (USA only) or mobile 
home, where not prohibited by local codes.

Cet appareil peut être installé dans un 
maison préfabriquée (É.-U. seulement) ou 
mobile  déjà  installée à demeure si les 
réglements locaux le permettent.

Test gauge connections are provided on 
the front of the millivolt gas control valve 
(identifi ed IN for the inlet and OUT for the 
manifold side).

These appliances and their individual shut-off 
valves must be disconnected from the gas 
supply piping system during any pressure 
testing of that system at pressures in excess 
of 1/2 psig (3.5 kPa)

.

These appliances must be isolated from the 
gas supply piping system (by closing their 
individual manual shut-off valve) during any 
pressure testing of the gas supply piping 
system at test pressures equal to or less than 
1/2 psig (3.5 kPa).

These appliances must not be connected to 
a chimney or fl ue serving a separate solid 
fuel burning appliance.

WARNING: This appliance must be properly 
connected to a venting system.  Operation 
of this gas appliance when not connected to 
a properly installed and maintained venting 
system can result in carbon monoxide (CO) 
poisoning and possible death.

Carbon Monoxide Poisoning: Early signs 
of carbon monoxide poisoning are similar 
to the fl u with headaches, dizziness and/or 
nausea. If you have these signs, obtain fresh 
air immediately. Turn off the gas supply 
to the appliance and have it serviced by 
a qualifi ed professional, as it may not be 
operating correctly.

The millivolt appliances are manually con-
trolled and feature a spark igniter (piezo) 
that allows the appliance's pilot gas to be 
lit without the use of matches or batteries.  
This system provides continued service in 
the event of a power outage.

Do not use these appliances if any part 
has been under water.  Immediately call a 
qualifi ed, professional service technician to 
inspect the appliance and to replace any parts 
of the control system and any gas controls 
which have been under water.

Burner Orifi ce Sizes

Model

No.

Nat.

Gas

Prop.

Gas

Elevation

Feet

(meters)

CI1500DVF

.104"

.061"

0-4500

(0-1372)

CI2500DVF

.121"

.068"

0-4500

(0-1372)

Table 4

Содержание 775



















Отзывы: