manualshive.com logo in svg

Leister WELDPLAST EC4, Руководство по эксплуатации, Страница: 18 / 20

Поделиться
Скачать
Leister WELDPLAST EC4 Скачать руководство пользователя страница 18

18

ACCESSORIES

Leister WELDPLAST S4 / EC4  hand extruder

37

39

38

41

40

41

Only Leister accessories may be used.

The 

universal tool stand

can

be used for the following 
extruder lines:   
– Fusion 3
– Weldplast 4
– Weldplast 6

• The 

hood (37)

is swivelled upwards for pre-heating the welding shoe.

• To adjust the stand, loosen the screws in the base and adjust the 

base plates (38)

to the tool markings.

• The two 

sliders (40)

allow the width to match the required tool.

• The 

reel holder (39)

serves to hold the reels of welding rod ø 300 mm.

• To ensure optimal rod dispensing, the welding rod should be passed through the

eyelets (41)

provided.

Hot - air tube on top

• The hot air tube is especially

suited for landfill sites.

Transportable welding rod
dereel holder  

• The holder is designed for

two welding rod reels with
ø 300 mm

• To ensure optimal rod

dispensing, the welding rod
should be passed through
the 

eyelets (41)

provided.

Содержание WELDPLAST EC4





















Отзывы:

Нет отзывов