background image

35

Rugby 200-3.2.1en

Safety Directions

Although the laser meets the strict 
regulations and standards which are in 
force in this connection, Leica 
Geosystems cannot completely 
exclude the possibility that the laser 
unit may be disturbed by very intense 
electromagnetic radiation, e.g. near 
radio transmitters, walkie-talkies, 
diesel generators, power cables.

Check the plausibility of results 
obtained under these conditions.

FCC Statement (applicable in 
the U.S.)

WARNING:

This equipment has been tested 

and found to comply with the limits for 
a Class B digital device, pursuant to 
part 15 of the FCC rules.

These limits are designed to provide 
reasonable protection against harmful 
interference in a residential 
installation.

This equipment generates, uses and 
can radiate frequency energy and, if 
not installed and used in accordance 
with the instructions, may cause 
harmful interference to radio 
communications. However, there is no 
guarantee that interference will not 
occur in a particular installation. If this 
equipment does cause harmful 
interference to radio or television 
reception, which can be determined by 
turning the equipment off and on, the 
user is encouraged to try to correct the 
interference by one or more of the 
following measures:

Increase the separation between 
the equipment and the receiver.

Consult the dealer or an 
experienced radio/TV technician for 
help.

Reorient or relocate the receiving 
antenna.

Connect the equipment into an 
outlet on a circuit different from that 
to which the receiver is connected.

WARNING:

Changes or modifications not 

expressly approved by Leica 
Geosystems could void the user's 
authority to operate the equipment.

This device complies with Part 15 of 
the FCC Rules. Operation is subject to 
the following conditions:  (1) This 
device may not cause harmful 
interference, and (2) this device must 
accept any interference received, 
including interference that may 
cause undesired operation.      

This device complies with Part 15 of  
the FCC Rules. Operation is subject to  
the following conditions:  (1) This  
device may not cause harmful  
interference, and (2) this device must  
accept any interference received,  
including interference that may  
cause undesired operation.      

Содержание Rugby 200





































Отзывы: