Leica Captivate Скачать руководство пользователя страница 285

Страница: 285 / 1060

Key

Description

To return to the

Leica Captivate - Home

Description of fields for the External page

Field

Option

Description

Rover

antenna

Selectable list Leica Geosystems antennas are predefined

as default and can be selected from the list.

Default antennas contain an elevation-

dependent correction model. New antenna

correction models can be set up and trans-

ferred to the instrument using Infinity. Open

the list to define or edit antennas.

Refer to "23.2.2 Antennas".

Vertical off-

set

Display only

The vertical antenna offset for the selected

antenna.

Antenna

height when

measuring

points

Editable field

Sets the default antenna height for the cur-

rent working style. This height is then also

the default antenna height during the use of

apps. The antenna height can still be

changed during a survey. The initial value

depends on the selected antenna.

Unavailable for SmartStation. The height is

added in the Setup and Measure app.

Use offset

for moving

antenna

Check box

When unchecked, the moving antenna height

is considered the same as the default

antenna height.

Show

antenna

type when

starting an

app

Check box

When this box is checked and an app with

measurement functionality is started, the

configured antenna type and offset are dis-

played in an information window.

Offset

Editable field

When the check box

Use offset for moving

antenna

is checked: Sets the offset to the

default antenna height for auto points and

for the moving part of a track when logging

raw observations.

23.2.2

Antennas

Listed are antennas in the instrument’s internal memory.

Open the selectable list for

Rover antenna

Antenna Heights

Description

Access

Settings - GS Sensor

285

Содержание Captivate





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Captivate

Отзывы:

Похожие инструкции для Captivate

Бренды по названию

Популярные бренды

Leica Captivate, Техническое справочное руководство

Результаты поиска

Содержание Captivate

Отзывы:

Похожие инструкции для Captivate

Бренды по названию

Популярные бренды