Leica Geosystems MX9400N Скачать руководство пользователя | Manualshive

Страница: 20 / 22

background image

WinFrog User’s Guide - Appendix C – GPS/MX 9400

Page 20 of

22

The data logged includes the time of the clock adjustment and the amount it was
adjusted.

Note that this is only in affect if Raw Data recording is turned on.

Monitoring the synchronization

The synchronization of the WinFrog clock can be monitored from the Calculation
Window using the Data Item Text and Time Series options.

In the Data Item Text panel, the following information is displayed:

•

Status
Displays the data type status (On/Off) and the associated device status.

•

Sync’d at
Displays the time the WinFrog clock was last adjusted.

•

Computer time
WinFrog clock time stamp of last synchronization data input

•

UTC time
UTC time (from device) of last synchronization data input

•

Raw Delta
The difference between the UTC and associated WinFrog time stamp (UTC –
WinFrog) for the last epoch

•

Filter Delta
The difference between the UTC and filtered WinFrog time for the last epoch

In the Time Series panel, the difference between the UTC time and the raw and filtered
WinFrog times are plotted.

«
...
18
19
20
21
22
»

Содержание MX9400N























Отзывы:

Нет отзывов

Похожие инструкции для MX9400N

Бренд: V7 Страницы: 8

echoMAP CHIRP 45 Series

Бренд: Garmin Страницы: 49

$Si-tex SVS-460 Operation Manual preview$

Бренд: Si-tex Страницы: 124

Бренд: Ubisense Страницы: 7

Бренд: Navman Страницы: 17

Бренд: CyBike Страницы: 2

Street Pilot 2720

Бренд: Garmin Страницы: 52

Бренд: Chinavision Страницы: 21

GPSMAP 296 - Aviation GPS Receiver

Бренд: Garmin Страницы: 2

Бренд: Dual Страницы: 20

NavAtlas XNAV3500P

Бренд: Dual Страницы: 32

Бренд: Xinuo Страницы: 83

Бренд: Car Secretary Страницы: 8

Бренд: VersaLogic Страницы: 14

Бренд: Vjoy Car Страницы: 2

Бренд: Vjoy Страницы: 20

Бренд: PORTMAN Страницы: 29

Бренд: Blue Sky Network Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды