background image

Doc No. FM0862 issue 3 Page 1  

1m        2m        3m        4m

 

2m 

 

1m

 

---------  

 

--------- 

 

 0.8m 

 

1m            2m            3m            4m

 

Walking Direction

 

169MHz Telecare Devices 

Floor PIR Motion Detector 

__________________________________________________________________________________________________________ 

 

 

 

 

 

 

 

 

 

 

Compatible with Reach at-home alarms, Advent XT warden call systems, 
Altec Response local carer alarms & Touchsafe Pro Nursecall systems 

 

Floor mounted passive infrared motion detector 

 

Operation and detection LED indicators  

 

2 No. user replaceable 1.5V AA Alkaline batteries 

 

Low battery warning 

 

Dimensions: 128mm x 57mm x 35mm (HxWxD) 

 

Weight: 128 grams inc. batteries 

 

Product Code: ZXT494 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

What can the PIR be used for? 

The Floor PIR motion detector monitors the presence of people and registers their movements. Movement will normally result in 
an alarm call being sent to the Care personnel. 

 

 

Where can the PIR be located 

The PIR is for indoor use only, it can be simply placed on the floor or on a table. The detection area is about 4 metres within a very 
narrow beam and shallow angle, see below... 
 
     

Floor Mounted Vertical Detection Area

   

 

Horizontal Detection Area

 

 
 

 

   -------------------------------------------------------- 

 

     

 

 

   -------------------------------------------------------- 

 

 
 
 
 

IMPORTANT:

 Care should be taken when placing the PIR to ensure the required area of detection is properly covered. It is best 

practice to place the PIR so the detection beam will be crossed by the walking direction you want to monitor. If setup for no 
entry/exit delay then the PIR should be placed so Carers can switch the PIR on/off when leaving and entering the room without 
passing the detection area. Always perform a walk test during installation. 

 
Placement & Safety Instructions 

 

 

Do not place items in front of the PIR detector 
which may restrict its field of view 

 

 

Do not drop the PIR detector or expose to high 
vibration or shock 

 

Do not expose the PIR detector to direct 
sunlight or powerful lights  

 

 

Do not use abrasive or corrosive cleaning agents  
or detergents when cleaning the PIR detector. 

 

Do not expose the PIR detector to rapid 
variation in temperature 

 

 

Do not disassemble the PIR detector or attempt to 
repair it yourself. 

 

Do not expose the PIR detector to wind, air 
conditioning or heating 

 

 

This product should not be a substitute for routine 
visual monitoring by a Carer. 

 

Do not expose the PIR detector to dripping or 
splashing water 

 

 

This product should be disposed of and recycled in 
accordance with the WEEE regulations. 

 
Maintenance 

No routine maintenance is required; however, a walk test should be performed once a month to verify operation.  
PIR

s are not as susceptible to dust and contamination as some detectors but it is still recommended to clean them periodically. 

PIR

’s

 can be dusted or wiped clean with a soft cloth, dampened slightly with mild soapy water. 

Do not clean with detergents, solvents or polish.

 

 
 
 
 
 
 

Tynetec and Aidcall are business units of Legrand Electric Ltd 

Unit 10 Cowley Road, Blyth Riverside Business Park, Blyth 

Northumberland, NE24 5TF. Tel: 

01670 352 371

 

Fax: 

01670 362 807

 

Email: 

[email protected]

  Web

www.tynetec.co.uk

 

Содержание Tynetec ZXT494








Отзывы: