background image

Operating Your Fireplace for the First Time

When operating your new 

fi

 replace for the 

fi

 rst time, 

some vapors may be released due to the burning of 
curing compounds used in the manufacture of the 
appliance. They may cause a slight odor and could 
cause the 

fl

 ames to be the full height of the 

fi

 rebox, or 

even slightly higher, for the 

fi

 rst few hours of operation.

It is also possible that these vapors could set off any 
smoke detection alarms in the immediate vicinity. 
These vapors are quite normal on new appliances. We 
recommend opening a window to vent the room. After 
a few hours use, the vapors will have disappeared and 
the 

fl

 ames will be at their normal height.

Flame Supervision Device

For your safety, this appliance is 

fi

 tted with a 

fl

 ame 

supervision device which will shut-off the gas supply 
if, for any reason, the pilot 

fl

 ame goes out. This device 

incorporates a 

fi

 xed probe, which senses the heat 

from the pilot 

fl

 ame. If the probe is cool, the device will 

prevent any gas 

fl

 ow unless manually lighting the pilot. 

See full lighting instructions on page 12 of this manual.

Owner’s Information

This manual and particularly the preceeding 
and following pages contain very important 
information regarding the safe operation of your 

fi

 replace as well as maintenance instructions.

Read carefully BEFORE operating your 

fi

 replace 

and pay special attention to the SAFETY 
WARNINGS.

A heating gas appliance does require safe handling 
and for this reason, we very strongly recommend that 
no children be allowed to touch the 

fi

 replace and its 

controls at all times. 

Do install a screen or barrier 

in front of the 

fi

 replace to protect your children 

against severe burns.

Thank You ...

For purchasing a Valor by Miles Industries. Your new 
radiant gas heater is a technical appliance that must 
be installed by a quali

fi

 ed dealer. Each Valor 

fi

 replace 

is fully tested during the production process for your 
safety and comfort.
Your unit has been professionally installed by:
Dealer Name: ________________________________
Phone Number :_______________________________

Should you encounter an operational problem, call 
your dealer immediately.
Do not try to repair the unit as you may cause an 
injury or damage the 

fi

 replace.

Performance of LPG appliances may be affected 
by the quality of commercial gas supplied in 
your area.

Do not put

 

furniture or other objects 

in this space in front of 

the fireplace:

36” (0.9 m)

Fireplace

Hearth

WARNING

EXTREMELY HOT!!!

• 

READ the SAFETY information on pages 
3 and 4 of this manual BEFORE operating 
your gas heater.

•  Some parts of your 

fi

 replace are 

EXTREMELY 

HOT

, particularly the 

GLASS

 window.

• 

DO NOT LET CHILDREN

 touch the glass or 

any parts of your 

fi

 replace 

even after it is 

turned off

 as it is still hot.

• 

USE THE BARRIER SCREEN provided with 
the appliance, front or trim or a GATE

 to 

reduce the risk of burns.

•  Keep the remote control handset 

OUT OF 

REACH

 of children.

• 

HOT HEARTH/FLOOR SURFACE!

 The 

hearth or 

fl

 oor directly in front of the 

fi

 replace 

is 

VERY HOT

 when the 

fi

 replace heats. Even 

if constructed of non-combustible materials, 
and although safe, it may reach temperatures

 

in excess of 200º F

 depending on choice of 

materials. 

DO NOT STEP ON IT!

• 

•  Some materials or items, although safe, may 

Some materials or items, although safe, may 
discolor, shrink, warp, crack, peel, and so on 

discolor, shrink, warp, crack, peel, and so on 
because of the heat produced by the 

fi

 replace. 

because of the heat produced by the 

fi

 replace. 

AVOID PLACING

AVOID PLACING

 candles, paintings, photos, 

 candles, paintings, photos, 

and other items 

and other items 

SENSITIVE TO HEAT

SENSITIVE TO HEAT

  within 

36 inches (0.9 m) around the 

fi

 replace.

• 

•  Solid wood 

fl

 ooring in front of the 

fi

 replace (if 

Solid wood 

fl

 ooring in front of the 

fi

 replace (if 

allowed) may shrink during the heating season 

allowed) may shrink during the heating season 
due to heat.

due to heat.

!

5

OWNER’S 
INFORMATION

Содержание 738JLN

































Отзывы: