Used units must not be disposed of with household waste!
If the unit is no longer operational, every consumer is required
by law to dispose of used devices separate from household
waste, e. g. at a collection point run by the communal authority
borough. In this way, used devices can be recycled and waste
materials disposed of in an environmentally friendly manner.
For this reason, electrical equipment is labeled with the dis-
played symbol.
Batteries and rechargeable batteries must not be disposed of
with household waste!
Every consumer is required by law to bring all batteries and re-
chargeable batteries to a collection point run by the communal
authority or borough or run commercially , so that they can be
disposed of in an environmentally friendly manner.
Please only hand in fully discharged batteries !
Ledino
Deutschland GmbH
the energy saving company
Albert-Einstein-Ring 27
14532 Berlin/ Kleinmachnow
Germany
Ledino
LED LIGHTING
the energy saving company
high energy saving • energy class A • long lifetime • low heat emission • 100 % light immediately • mercury-free
The fl ood light LED FLG50TW is only full functional with the remote
control LED TW1. The remote control can operate up to 99 LED fl ood
lights. Please, buy both devices separately.
35 W LED-Flood Light, turnable white
LED-FLG50TW
Remote control
LED-TW1
IMPORTANT!:
Read all instructions carefully. If you do not understand this instruction, contact
your dealer. Check the device for transport damage. Those has to be reported
to the forwarder/carrier.
SAFETY:
Danger to life! The wiring must run according to local statutory regulations and
guidelines. All work must be carried out only by a qualifi ed electrician.
WARNING:
Disconnect power during installation and before servicing. These procedures
should only be performed by a qualified electrician. Supply power should be
turned off when replacing components or checking connections. Never
perform maintenance or cleaning while electric tension is not de-energized.
Leading in design and technology!
Protected design!
Ledino LED Flood Light, Turnable White
Brig white light colour (K) per
RF remote control adjustable.
180-260 V AC 50/60 Hz, max. 35 W
40 W LED chip (80 lm/ W)
max. 2070 lm, energy class A
2700-7300 K,120° beam angle
operating temperature: -20 up to 40 °C
50 cm connecting cable
aluminium housing, silver
IP65 - protection against jets of water
W: 225 mm, H: 185 mm, D: 130 mm, 2.1 kg
Ledino RF Remote Control
Frequency: 2.4 GHz
Battery: 2x AAA (not included)
Eff ective distance: up to 20 m
The remote control is suitable for indoor use only.
Protect the device against moisture.
Remove batteries from devices that will be stored
for extended periods.
Setup ID number of lamps:
1. Power on the lamp you want to set (light on).
2. Press ⑪ 1 or 2 keys (choose ID number), then press key „ID“ ⑬.
3. Repeat step 2 again. The lamp will turn off automatically.
4. Power off the lamp within 10 sec. then fi nish setup.
5. If the lamp turns on again automatically, setup is canceled. Please try it again.
Function Lamps:
- On left side you see the function of keys ①-⑬.
- Press the key for ID number ⑪ of the choosen lamp or „ALL“ ⑦ for all connected lamps,
than press a functional key e. g. ON/ OFF, colour temperature or brightness.
-
Night light mode:
Press key ① when lamp is turn off , the lamp turn on in night light mode
with brightness of 3%.
-
Timer set:
Press the key for ID number ⑪ of the choosen lamp, than the ID key ⑬.
Press keys ⑪ (1-99) for numbers of time units, then key „Timer ON“ ⑥ (turn light on) or
„Timer OFF“ ⑥ (turn light off ). One time unit is 10 minutes.
Timer cancel:
Press key „0“ ⑪, than key „Timer ON“ ⑥ or „Timer OFF“ ⑥.
-
Save Scene:
Lamp can save 2 scenes (A+B). Adjust light as your preference. Press the key
for ID number ⑪ of the choosen lamp, than the ID key ⑬ and than scene mode key ⑩ „A“
or „B“. The Lamp will save the status of lamp.
Recall Scene:
Press the key for ID number ⑪ of the choosen lamp, than scene mode key ⑩
„A“ or „B“.
-
Circle mode:
Press the „ON“ key ② twice within 3 Seconds, the circle mode will begin to show
diff erent state of the lamp.
-
Copy ID of remote control to a second remote control:
Press the „S“ key ⑫ of controller 1
and the key „ON“ key ② of the controller 2 at the same time for 10 seconds. Keep the dictance
between controllers within 10 cm.
Recover:
Press the „S“ key ⑫ of controller 1 and „ALL“ ⑦ of the controller 2 for 10 seconds,
the controller will recover its ID.
LED-FLG50TW
②
ON
③
OFF
④
Colour temperature
①
Night light mode
⑧
Colour temperature
⑥
Timer ON/ OFF
⑦
Choose all lamps
⑤
Brightness
⑨
Brightness
⑩
Scene mode keys
⑪
Nummeric keys
⑫
Copy the ID of
remote control
⑬
ID setting key
LED-TW1
