background image

MM400C

LECTROSONICS, INC.

8

Controls and Functions

Preventing Internal Corrosion

It is very important that you properly dry the transmitter 

when it becomes wet due to immersion or high levels of 

perspiration 

BEFORE opening any covers or connec-

tors.

 Follow the procedure below for best results:

1.  Carefully blot the transmitter dry with a clean paper 

towel or cloth. 

Remove all moisture.

  After open-

ing any connector or cover, carefully blot up any 

remaining moisture that may have remained around 

the seal. 

 

IMPORTANT!

  DO NOT CLOSE ANY COVER 

OR CONNECTOR BEFORE MAKING CERTAIN 

THERE IS NO MOISTURE IN OR NEAR THE 

OPENING.

2.  After use, it is important to store the transmitter 

in a dry place with all access compartments and 

connectors opened to allow any internal humidity to 

evaporate.  Specifically, open the Battery Compart

-

ment, the Frequency Switch Cover Plate and fully 

unscrew and remove the microphone connector 

before storing.  

Do not store wet and do not store 

sealed.

  If moisture is sealed inside the unit it has 

nowhere to go other than to chemically react with 

and destroy components and the printed circuit 

board.

3.  Lubricate all rubber O-rings with petroleum jelly 

(such as Vaseline) after each use (included with 

transmitter and O-ring replacement kits). 

DO NOT 

USE ANYTHING OTHER THAN PURE PETRO-

LEUM JELLY.

 Silicone-based lubricants will dis-

solve the rubber. Failing to lubricate the O-rings 

after each use will significantly shorten their life.

Power ON/OFF Switch

A waterproof, magnetic Power ON/OFF switch is 

located on the unit’s side panel.  The switch actually 

consists of two components.  A magnetically actuated 

internal component and a magnet housing assembly.  

The switch is designed so that the unit will still operate 

if the Switch Magnet Housing Assembly is missing or 

removed.

The function of the Power ON/OFF Switch can also be 

changed so it operates as an audio mute switch.  (See 

Operating Instructions,  Power Switch Function Selec-

tion

.)  These functions are illustrated in the chart below:

 

Power Switch Position

Function 

ON 

OFF

Normal, or 

Applies Power 

Turns Unit Off

 

Power Mode 

to Unit

Audio Mute  

Turns On Audio 

Mutes Audio

 

Mode
 

If the MM400C Power ON/OFF Switch has been con

-

figured for Audio Mute Mode, it is still possible to turn 

off the transmitter without removing the battery.  This 

is done by placing the switch in the ON position, then 

toggling the switch between the ON and OFF position 

three times in less than five seconds, i.e., ON (Starting 

Position)-OFF-ON-OFF-ON-OFF. 
The user-selected configuration of the Power ON/OFF 

switch is stored in memory and persists until reconfig-

ured by the user.

Power LED

The PWR LED provides an indication of the battery’s 

condition.  The PWR LED glows green when the battery 

is good. The color changes to red when there is about 

30 minutes of operation left with the recommended 

lithium battery. (An alkaline battery will have about 20 

minutes of life left.)  When the LED begins to blink red, 

there are only a few minutes of life left in the battery.  

The PWR LED blinks red for a short period when the 

transmitter is configured for Normal Mode and the 

Power ON/OFF switch is set to OFF.  At the end of the 

power off sequence, then PWR LED extinguishes.

Note: A NiMH battery gives little or no warning 

when it is depleted.  If you use NiMH batteries in 

the MM400C, we recommend trying fully charged 

batteries first, noting the length of time that the 

batteries will run the unit , then plan for somewhat 

less time  to determine when the battery needs to 

be replaced. Some Lectrosonics receivers have 

timers for use with these batteries.

A weak battery will sometimes cause the PWR LED to 

glow green immediately after being put in the unit, but 

will soon discharge to the point where the LED will blink 

red or shut off completely.

Microphone Jack

Frequency Select 

SwitchThumbscrew

and Cover Plate

Modulation and

Power LEDs

Audio  Level Control

Antenna

Battery 

Compartment 

Cap

Power ON/OFF Switch 

(External Switch Magnet 

Housing Assembly Shown.)

Содержание MM400C





















Отзывы: