manualshive.com logo in svg

Lectrosonics DSP4/4, Инструкция по эксплуатации и руководство по устранению неисправностей, Страница: 31 / 34

Поделиться
Скачать
Lectrosonics DSP4/4 Скачать руководство пользователя страница 31

31

4 In / 4 Out Digital Audio Processor

Rio Rancho, NM – USA

SPECIFICATIONS

Connectors

Audio:

5-pin Phoenix style

Exp In/Out:

8-pin mini DIN

Programmable I/O:

15 pin D-Sub

LecNet RS-232:

3.5mm Stereo jack

Audio Inputs

Line Input Type:

Electronically Balanced and RF Filtered

Input Impedance:

>40k Ohms, Balanced/Unbalanced

Maximum Input Level:

+20dBu

Gain Range:

+10dB to -68dB, plus off

Outputs

Line Output Type:

Electronically Balanced and RF filtered

Output Impedance:

200 ohms balanced, 100 ohms unbalanced

Output Gain Range:

0dB to –78dB, 1dB steps, plus mute

Maximum Output Level:

+20dBu

Matrix Crosspoints

Matrix Crosspoint
Gain Settings:

+10dB to -20dB, plus of f in 1dB steps

User Defined Filters

Types Available:

1st order highpass and lowpass
2nd order highpass, bandpass, and lowpass
1st order shelving bass and treble
2nd order shelving bass and treble
Parametric

Feedback Eliminator (ADFE)

Filter Type:

1/5 octave notch, placed with 1/10
octave accuracy

Filter Cut:

-6dB, -12dB

Filter Range:

100Hz to 5.6kHz

Compressor

Attack Time:

0.5mS to 128mS in 0.5mS steps

Release Time:

10mS to 2.55S in 10mS steps

Threshold:

+20dBu to -40dBu in 1dB steps

Compression Ratio:

1:1, 1.5:1, 2:1, 3:1, 4:1, 5:1

Limiter

Attack Time:

0.125mS to 32mS in 0.125mS steps

Release Time:

2mS to 512mS in 2mS steps

Threshold:

+20dBu to -40dBu in 1dB steps

Digital Delay

Delay Time:

182.625mS maximum, in 20.83uS steps

Programmable Inputs/Outputs

Programmable Input Range: 0VDC - 5VDC
Analog Control:

0dB to -30dB plus off control range
156mV/dB control sensitivity

Logic Control:

Active Low

Programmable Output:

Active low
Max sink current:

100 mA

Max supply voltage:

 40VDC

Serial Communication

Default LecNet Address:

DSP4/4: 143; DSP4/4 Dual: 143, 144

Serial Comm Parameters:

RS-232, 9600 baud, 8 data bits, no parity,
1 stop bit

System:

Overall Latency:

3 ms

System THD:

Less than 0.05%, +20dBu in, +20dBu out

System IMD:

Less than 0.05%

Power Consumption:

DSP4/4: 10 Watts max at 16.5VAC;
Dual: 20 Watts max at 16.5VAC

Weight:

3.5 lbs. (4 lbs for dual)

Dimensions:

19" wide x 1.75" high x 8" deep

FCC PART 15 NOTICE

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful
interference in a residential installation.  This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the  instructions, may cause harmful interference
to radio communications.  If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Содержание DSP4/4



































Отзывы:

Нет отзывов