Lectrosonics DMTH4 Скачать руководство пользователя страница 61

Страница: 61 / 70

Digital Telephone Hybrid

Rio Rancho, NM

telflash (flash telephone hookswitch)

This command may be used to “flash” the telephone

hookswitch (momentarily break and then re-make the

connection).
Example:

Request

Response

Command

telflash?<CR>

OK<CRLF>

telnbr (stored telephone number)

This command may be used as a query to read a stored

telephone number, or as an update to store a telephone

number string. The position in the “phone book” storage

is specified by using the address syntax. Addresses

must be in the range 1 to 32. The data type is string, with

a limit of 30 characters. Only

certain characters are

meaningful in telephone number strings. Other charac-

ters are permitted, but ignored when dialing.
Examples:

Request

Response

Query

telnbr(1)?<CR> OK

“555-5555”<CRLF>

Update

telnbr(12)=

”1-555-555-5555”<CR> OK<CRLF>

telnbrti (stored telephone number title)

This command may be used as a query to read a stored

telephone number title, or as an update to store a

telephone number title string. The position in the “phone

book” storage is specified by using the address syntax.

Addresses must be in the range 1 to 32. The data type is

string, with a limit of 30 characters.
Examples:

Request

Response

Query

telnbr(1)?<CR>

OK “Joe’s

Muffler Shop”<CRLF>

Update

telnbr(12)=

”1-555-555-5555”<CR> OK<CRLF>

telpriv (telephone line privacy)

This command may be used as a query to determine the

privacy status of the telephone line interface. It may also

be used as an update to enable or disable the privacy

feature on the telephone line interface. The data type

is integer, either “1” meaning enabled, or “0” meaning

disabled.
Examples:

Request

Response

Query

telpriv?<CR>

OK 0<CRLF>

Update

telpriv=1<CR> OK<CRLF>

telprivmod (telephone line privacy mode)

This command may be used as a query to read the pri-

vacy mode setting for the telephone line interface. It may

also be used as an update to set the privacy mode. The

data is an integer type. The following values are allowed:

1 means that only telephone transmit audio is muted

when privacy is enabled

2 means that only telephone receive audio is muted

when privacy is enabled

3 means that both telephone transmit and receive

audio are muted when privacy is enabled

Examples:

Request

Response

Query

telprivmod?<CR>

OK 3<CRLF>

Update

telprivmod=2<CR> OK<CRLF>

telrchmlv (telephone ring chime level)

This command may be used as a query to read the tele-

phone ring chime level, or as an update to set the level.

The data type is integer, in the range -12 to +12, repre-

senting dB relative to the normal audio level.
Examples:

Request

Response

Query

telrchmlv?<CR>

OK -3<CRLF>

Update

telrchmlv=0<CR> OK<CRLF>

telredial (redial last number)

This command may be used to redial the last dialed

telephone number.
Example:

Request

Response

Command

telredial<CR> OK<CRLF>

telringchm (telephone ring chime)

This command may be used as a query to determine the

status of the telephone ring chime feature. It may also be

used as an update to enable or disable the ring chime.

The data type is integer, either “1” meaning enabled, or

“0” meaning disabled.
Examples:

Request

Response

Query

telringchm?<CR>

OK 0<CRLF>

Update

telringchm= 1<CR>

OK<CRLF>

Содержание DMTH4







































































Результаты поиска

Содержание DMTH4

Отзывы:

Бренды по названию

Популярные бренды

Lectrosonics DMTH4, Справочное руководство

Результаты поиска

Содержание DMTH4

Отзывы:

Бренды по названию

Популярные бренды