Leadshine EM522-CAN Скачать руководство пользователя страница 8

Страница: 8 / 33

EM522-CAN Field bus Stepper Drive User Manual V1.0

IN1+

Opto-isolation differential input signals (5-24V compatible)

IN1-

IN2+

IN2-

IN3+

IN3-

ALM+

Opto-isolation differential output signal is for alarm function. maximum output current 100mA,

maximum pull-up voltage 24VDC

ALM-

Notice

Notes:

(1) The function of input signals can be configured by controller

3.1.2 Connector P2

Pin Function

Details

GND

Power supply ground connection.

+VDC

Power supply positive connection. Suggest 24-48VDC power supply voltage

A+, A-

Motor Phase A connections. Connect motor A+ wire to A+ Pin; motor A- wire to A-

B+, B-

Motor Phase B connections. Connect motor B+ wire to B+ Pin; motor B- wire to B-

Warning

Warning:

(1) Don’t plug or unplug the P2 terminal block to avoid drive damage or injury when EM522-CAN is

powered on; (2) Don't connect the power supplier to motor connection terminal, and don't cVDC and GND

inversely, otherwise, drive will be damaged.

3.1.3 Connector P3

CAN port of EM522-CAN adopt shield doublet RJ45 terminal (standard RJ45 specification).

PIN definition

Signal

Details

CAN_H

Differential signal of CAN

CAN_L

CAN_GND

CAN ground

4-8

Notice

Notes:

(1) shielding cable and reliable grounding is suggested; (2) CAN_H and CAN_L should not connect

inversely; (3) Two interfaces of RJ45 without order.

3.2 DIP Switch

EM522-CAN field bus stepper drive uses an 8-bit DIP switch to set CAN ID, baud rate, as shown below:

Содержание EM522-CAN


































Результаты поиска

Содержание EM522-CAN

Отзывы:

Похожие инструкции для EM522-CAN

Бренды по названию

Популярные бренды

Leadshine EM522-CAN, Руководство пользователя

Результаты поиска

Содержание EM522-CAN

Отзывы:

Похожие инструкции для EM522-CAN

Бренды по названию

Популярные бренды