Leader Electronics Corp. LT 443D Скачать руководство пользователя страница 113

Страница: 113 / 239

HD/HDB-24

4.12

EXIT

Select [EXIT] from the [1. GENLOCK SETTING] menu, then press the [ENTER] key. The

status display screen is displayed.

1. HD SETTING

▲

EXIT

Hierarchy level 1

4.13

Notes on Reading Preset Data

See note below when using “PRESET/RECALL” function in the “UTILITY MENU” while

displaying the NATURAL PICTURE (i.e., FILE TRANSFER executed).

When new preset data is read by changing a CF card, transfer the NATURAL PICTURE

again (FILE TRANSFER).

(No NATURAL PICTURE transfer is required if preset data with different picture size is

read.)

4.11.2 TIMING

This section describes setting procedure of the serial digital (SDI black) signal timing with

respect to the internal reference signal (i.e., frame reset signal).

(1) Setting procedure is the same as the Section 4.3, “HD TIMING.”

4.11.3 EMBEDDED AUDIO

This mode is used to set the embedded audio signal (e.g., audio signal on or off, audio

data resolution, emphasis, channel selection) in each group.

The relationship between the group and channel numbers is as follows:

[GROUP 1]: CH 1 to CH 4

[GROUP 2]: CH 5 to CH 8

[GROUP 3]: CH 9 to CH 12

[GROUP 4]: CH 13 to CH 16

(1) Setting procedure is the same as the Section 4.4, “EMBEDDED AUDIO.”

Содержание LT 443D
















































































































































































































































Результаты поиска

Содержание LT 443D

Отзывы:

Похожие инструкции для LT 443D

Бренды по названию

Популярные бренды

Leader Electronics Corp. LT 443D, Инструкция по эксплуатации

Результаты поиска

Содержание LT 443D

Отзывы:

Похожие инструкции для LT 443D

Бренды по названию

Популярные бренды