manualshive.com logo in svg

LAWN STAR LSPS 5850, Руководство по эксплуатации, Страница: 4 / 23

Поделиться
Скачать
LAWN STAR LSPS 5850 Скачать руководство пользователя страница 4

 

4 

  With a basic understanding of kickback you can reduce or eliminate the element of 

surprise. Sudden surprise contributes to accidents. 

  Keep a good grip on the saw with both hands, the right hand on the rear handle, and 

the left hand on the front handle, when the engine is running. Use a firm grip with 
thumbs and fingers encircling the chain saw handles. A firm grip will help you reduce 
kickback and maintain control of the saw. 

  Make certain that the area in which you are cutting is free from obstructions. Do not 

let the nose of the guide bar contact a log, branch, or any other obstruction which 
could be hit while you are operating the saw. 

  Do not overreach or cut above shoulder height. 

  Follow manufacturers sharpening and maintenance instructions for saw chain. 

  Only use replacement bars and chains specified by the manufacturer or the 

equivalent.  

  If possible, use a log stand for cutting loose logs. 

  Always keep aware of the bar tip relative to other objects. 

  Cut at high engine speeds. Never start the machine while the chain rests on an 

object. 

  Piercing cuts with the bar tip may only be performed by trained and experienced 

operators. 
 

E)  Instructions on safe working techniques 

 

  Always maintain a normal body posture when operating the device. Always keep your 

balance. 

  Do not work with your body bent forwards. 

  Do not work on ladders, scaffolding, walls or trees. 

  Do not use the chain saw above shoulder height. 

  Do not cut plastic or other material. This chain saw is only intended for cutting wood. 

  Ensure that the wood cannot twist while it is being cut. 

  Never climb in a tree to cut branches. 

  Watch out for splintering wood. While you are sawing you may be injured by flying 

wood chips. 

  Do not use the chain saw to lever or move the wood. 

  Only cut with the lower section of the saw. The saw will be repulsed towards you if 

you try and cut with the upper section of the saw. 

  Ensure that the wood is free from of stones, nails and other foreign objects. 

  First-time users must obtain practical training in the correct use of the chain saw and 

the required safety equipment from an experienced operator. 

  Keep the running chain saw from touching the ground or wire fences. Do not cut thin 

wood or timber that is already sawn into small pieces. 

  Do not use the chainsaw as a lever for lifting or moving objects. 

  DO NOT fasten tools or accessories to the chainsaw that are not specified by the 

chainsaw manufacturer. 

 
 
ATTENTION: SAFETY FEATURES 
Safety features are designed to protect you against injuries and must not be altered or 
circumvented. 
 
 

Содержание LSPS 5850
























Отзывы:

Нет отзывов