manualshive.com logo in svg

LAWN STAR LSPS 5850, Руководство по эксплуатации, Страница: 20 / 23

Поделиться
Скачать
LAWN STAR LSPS 5850 Скачать руководство пользователя страница 20

 

20 

TROUBLE SHOOTING GUIDE 

 

PROBLEM 

PROBABLE CAUSE 

CORRECTIVE ACTION 

 

 

 

Engine won’t start 

No spark  

Ensure the spark plug is clean. 
Replace the spark plug if upon 
inspection the electrodes are burned 
or worn. Check the spark plug gap 
(Fig.23) with a feeler gage. Check for 
spark by using a Spark Tester. 

 

 

 

 

No fuel 

Pump primer bulb, if no fuel flows 
then pipes blocked. Have serviced. If 
primer bulb fills then engine may be 
flooded 

 

 

 

 

Flooded engine 

Remove spark plug, turn engine 
upside down, set choke to run, pull 
starter cord 10 times, clean spark 
plug and refit. 

 

 

 

 

Check fuel/oil mix 

Drain and use fresh and correct fuel 
mix 

 

 

 

Engine will not rev 

Carburettor needs 
tuning 

Have serviced 

 

 

 

 

Blocked exhaust spark 
arrestor 

Remove spark arrestor, clean & refit 

 

 

 

Engine Smokes and 
will not rev 

Incorrect fuel mixture 
too much oil 

Drain and use fresh and correct fuel 
mix (Oil/Fuel mix ratio 1:25) 

 

 

 

 

Dirty air filter or fuel 
filter 
 
Incorrect oil used 

Clean as per instructions 
 
 
Use Lawn Star High performance 2-
stroke engine oil (90-20000)  

 

 

 

Chain does not run 

Chain brake is on 

Check the position of the chain brake 
guard. The chain will only run if chain 
brake guard is released and locked 
into position. 

 

 

 

Chain oil does not 
flow 

Check oil level 

Top up oil 

 

 

 

 

Blocked oil flow 
openings 

Clean the oil flow ports and passages 
for clogging 

 

 

 

 

Poor quality / wrong 
grade oil 

 

 

 

 

Oil leaks out of 
exhaust muffler 

Incorrect fuel mixture 
too much oil 

Drain and use fresh and correct fuel 
mix (Oil/Fuel mix ratio 1:25) 

 

 

 

 

 

 

 

 

 

Содержание LSPS 5850
























Отзывы:

Нет отзывов