background image

9

3352-964 Rev B

Checking the Blade Brake

Clutch

Check the blade control bar before each use to

ensure that the blade brake clutch (BBC) system is

operating properly.

Not Using the Grass Bag

1.

Move the mower onto a paved surface in a

non-windy area.

2.

Set all 4 wheels to the (3-inch or 76 mm) cut

setting.

3.

Take a half sheet of newspaper and crumple it

into a ball small enough to go under the mower

housing (about 3 inches or 76 mm in diameter).

5 in. (13 cm)

m-8117

4.

Place the newspaper ball about 5 inches (13 cm)

in front of the mower.

5.

Start the engine.

6.

Engage the blade.

7.

Release the blade control bar.

8.

Immediately push the mower over the newspaper

ball.

9.

Stop the engine and wait for all moving parts to

stop.

10.

Go to the front of the mower and check the

newspaper ball.

Note:

 If the newspaper ball did not go under the

mower, repeat steps 4 through 10.

11.

If the newspaper is unravelled or shredded, the

blade did not stop properly, which could result in an

unsafe operating condition. Contact an Authorized

Service Dealer.

Using the Grass Bag

You can use the grass bag to perform an additional

test to check the BBC mechanism.

1.

Install the empty grass bag on the mower.

2.

Start the engine.

3.

Engage the blade.

Note:

 The bag should begin to inflate, indicating

that the blade is engaged and rotating.

4.

Release the blade control bar.

Note:

 If the bag does not immediately deflate, the

blade is still rotating. The BBC mechanism may be

deteriorating and, if ignored, could result in an unsafe

operating condition. Have the mower inspected and

serviced by an Authorized Service Dealer.

5.

Stop the engine and wait for all moving parts to

stop.

Mulching the Clippings

Your mower comes from the factory ready to mulch

the grass and leaf clippings back into the lawn.
If the grass bag is on the mower, remove it (refer to

Removing the Grass Bag on page 10) before

mulching the clippings. If the side discharge chute is

on the mower, remove it and lock the side discharge

door (refer to Removing the Side Discharge Chute on

page 11) before mulching the clippings.

Important

: Ensure that

the mulch plug (A) is

locked in place at both

the top and the bottom

before you mulch the

clippings.

A

m-7967

Bagging the Clippings

Use the grass bag when you want to collect grass

and leaf clippings from the lawn.
If the side discharge chute is on the mower, remove it

and lock the side discharge door (refer to Removing

the Side Discharge Chute on page 11) before bagging

the clippings.

Warning

The blade is sharp; contacting the blade can

result in serious personal injury.
Stop the engine and wait for all moving parts to

stop before leaving the operating position.

Содержание Insight 10697





















Отзывы: