Lawn-Boy Insight 10697 Скачать руководство пользователя

Страница: 15 / 20

3352-964 Rev B

Push the cable jacket upward 1/8 inch (3 mm).

Note:

You can place a ruler against the upper side

of the black cable mount (C) and measure how far

the upper end of the cable jacket (D) moves.

Note:

Moving the cable jacket upward decreases

the ground speed; moving the jacket downward

increases the ground speed.

Tighten the nut firmly.

Start the mower and check the adjustment.

Note:

If the self-propel is not properly adjusted,

repeat this procedure.

Replacing the Blade

Important

You will need a torque wrench to

install the blade properly.

If you do not have a

torque wrench or are uncomfortable performing this

procedure, contact an Authorized Service Dealer.
Examine the blade whenever you run out of gasoline.

If the blade is damaged or cracked, replace it

immediately. If the blade edge is dull or nicked, have

it sharpened or replace it.

Warning

The blade is sharp; contacting the blade can

result in serious personal injury.
Wear cloth or leather gloves when servicing the

blade.
1.

Disconnect the spark plug wire from the spark

plug. Refer to Preparing for Maintenance on page 12.

Tip the mower onto its side with the air filter up.

Remove the 2

blade nuts (A) and

the stiffener (B).

m-8071

Remove the blade.

Install the new blade.

Install the stiffener you removed in step 3.

Install the blade bolts and torque them to 15 to

27 ft-lb (20 to 37 N

⋅

m).

Cleaning the Blade Brake

Clutch Shield

Clean the blade brake clutch (BBC) shield at least

every 25 operating hours or yearly to prevent the

blade from stalling while you mow.

Disconnect the spark plug wire from the spark

plug. Refer to Preparing for Maintenance on page 12.

Tip the mower onto its side with the air filter up.

Remove the

2 blade nuts (A)

and the

stiffener (B).

Remove the

blade (C).

Remove the

blade driver (D)

and disk (E).

Remove the

BBC shield (F).

m-8071

Brush or blow out debris from the inside of the

shield and around all the parts.

Install the BBC shield that you removed in step 6.

Install the blade driver that you removed in

step 5.

10.

Install the blade and the stiffener that you

removed in steps 3 and 4.

11.

Install the blade bolts and torque them to 15 to

27 ft-lb (20 to 37 N

⋅

m).

Содержание Insight 10697





















Результаты поиска

Содержание Insight 10697

Отзывы:

Похожие инструкции для Insight 10697

Бренды по названию

Популярные бренды

Lawn-Boy Insight 10697, Руководство оператора

Результаты поиска

Содержание Insight 10697

Отзывы:

Похожие инструкции для Insight 10697

Бренды по названию

Популярные бренды