background image

26

troubleshooting

Problem

Possible Case

Solution

Heater fires, but Main 

PCB shuts heater off 

after a short period of 

time. Lamp is flickering, 

and LED display

shows “E1”.

1. Incorrect pump pressure

2. Dirty Input, Output or Lint 

Filter

3. Dirty Fuel Filter

4. Nozzle is Dirty

5. Photocell lens is Dirty

6. Photocell not installed 

properly

7. Photocell Defective

8. Improper electrical 

connection between Main 

PCB and Photocell.

1. Adjust Pump Pressure

2. Clean/replace Air Filter

3. Clean/replace Fuel Filter

4. Clean/replace Nozzle 

5. Clean/replace Photocell 

6. Adjust Photocell position 

7. Replace Photocell

8. Check wiring connections 

Heater will not operate, 

or motor runs for short 

time. Lamp flickers and 

LED display shows “E1”.

1. No kerosene in fuel tank

2. Incorrect pump pressure

3. Corroded Spark Plug or 

incorrect plug gap.

4. Dirty Fuel Filter

5. Dirty Nozzle

6. Moisture in Fuel/Fuel Tank

7. Improper electrical 

connection between 

Transformer and Circuit 

Board

8. Igniter Wire not connected 

to Spark Plug

9. Defective Igniter

1. Fill tank with fresh kerosene

2. Adjust Pump Pressure

3. Clean/replace Spark Plug

4. Clean/replace Fuel Filter

5. Clean/replace Nozzle

6. Rinse out fuel tank with clean 

fresh kerosene

7. Inspect all electrical 

connections. See Wiring 

Diagrams

8. Re-attach Igniter wire to Spark 

Plug

9. Replace Igniter

Fan does not operate 

when heater is plugged 

in and Power Switch is 

in the “ON” position. The 

lamp is flickering or on 

and LED Display shows 

“E1” or “E2”.

1. Thermostat is set too low

2. Broken electrical 

connection between Main 

PCB and motor

1. Rotate thermostat to a higher 

setting

2. Inspect all electrical 

connections. See Wiring 

Diagrams

Poor Combustion 

and / or excess soot 

production

1. Dirty Input, Output or Lint 

Filter

2. Dirty Fuel Filter

3. Poor quality of fuel

4. PSI is too high or too low

1. Clean/replace Air Filter

2. Clean/replace Fuel Filter 

3. Be sure fuel is not contaminated 

or old

4. Use proper pressure

Heater does not turn on 

and the lamp is not lit

1. Temperature limit sensor 

has overheated

2. No electrical power

3. Fuse Blown

4. Improper electrical 

connection between 

Temperature Limit Sensor 

and Circuit Board

1. Push Power Switch to “OFF” 

and allow heater to cool for 10 

minutes. Push Power Switch to 

back to “ON”

2. Check power cord and 

extension cord to insure of 

proper connection. Test power 

supply

3. Check/replace Fuse

4. Inspect all electrical 

connections. Wiring Diagrams

Troubleshooting

TROUBLESHOOTING CHART

HK175FH_LavorPro Heater_Manual_2016.indd   26

2016-04-01   11:39 AM

Содержание HK175FH





























Отзывы: