background image

Superabrasive 

Owner’s Manual Original Language – Lavina 

®

V25G-X  

08/2019 

 

 

35

 

GENERAL EMISSIONS WARRANTY COVERAGE 
Superabrasive Inc. warrants to the ultimate purchaser and each subsequent purchaser that the equipment is:  
Designed, built and equipped so as to conform with all applicable regulations; and 
Free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material 
respects to that part as described in Superabrasive Inc. application for certification. 
The warranty period begins on the date the equipment is delivered to an ultimate purchaser or first placed into service. 
The warranty period is two years. 
Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows: 
 
 (1)Any  warranted  part  that  is  not  scheduled  for  replacement  as  required  maintenance  in  the  written  instructions 
supplied, is warranted for the warranty period stated above. If the part fails during the period of warranty coverage, the 
part  will  be  repaired  or  replaced  by  Superabrasive  Inc.  according  to  subsection  (4)  below.  Any  such  part  repaired  or 
replaced under warranty will be warranted for the remainder of the period. 
(2)Any  warranted part that is scheduled only for regular inspection in the  written instructions supplied  is warranted for 
the warranty period stated above. Any such part repaired or replaced under warranty will be warranted for the remaining 
warranty period. 
(3)Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is 
warranted for the period of time before the first scheduled replacement date for that part. If the part fails before the first 
scheduled replacement, the part will be repaired or replaced by Superabrasive  Inc. according to subsection (4) below. 
Any  such  part  repaired  or  replaced  under  warranty  will  be  warranted  for  the  remainder  of  the  period  prior  to  the  first 
scheduled replacement point for the part. 
(4)Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty 
station at no charge to the owner. 
(5)Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers 
that are franchised to service the subject engines or equipment. 
(6)The  SORE  owner  will  not  be  charged  for  diagnostic  labor  that  is  directly  associated  with  diagnosis  of  a  defective, 
emission-related warranted part, provided that such diagnostic work is performed at a warranty station. 
(7)Superabrasive Inc. is liable for damages to other engine or equipment components proximately caused by a failure 
under warranty of any warranted part. 
(8)Throughout  the  SORE  warranty  period  stated  above,  Superabrasive  Inc.  will  maintain  a  supply  of  warranted  parts 
sufficient to meet the expected demand for such parts. 
(9)Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided 
without charge to the owner. Such use will not reduce the warranty obligations of Superabrasive Inc. 
(10)Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-
exempted  add-on  or  modified  parts  by  the  ultimate  purchaser  will  be  grounds  for  disallowing  a  warranty  claims. 
Superabrasive Inc. will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on 
or modified part. 
WARRANTED PARTS 
The repair or replacement of any  warranted part otherwise  eligible for warranty  coverage may be  excluded from such 
warranty  coverage  if  Superabrasive  Inc.  demonstrates  that  the  SORE  has  been  abused,  neglected,  or  improperly 
maintained,  and  that  such  abuse,  neglect,  or  improper  maintenance  was  the  direct  cause  of  the  need  for  repair  or 
replacement of the part. That notwithstanding, any adjustment of a component that has a factory installed, and properly 
operating,  adjustment  limiting  device  is  still  eligible  for  warranty  coverage.  The  following  emission  warranty  parts  are 
covered: 
(1)Catalytic converter 
(2)Fuel system: Carburetor, pressure regulator and fuel lock off 
(3)Ignition system 
(4)Intake system including pre-filter 
(5)Exhaust manifold 

 

 
 

 
 

Содержание V25G-X




































Отзывы: